Hi, this is my first post here and I have installed slitaz 4.0 on an older computer:
Pentium III, 600 MHz, 256MB ram, 20GB HDD, motherboard is a M748LMRT with onboard SiS shared graphics.
Anything I do in the GUI environment is just really slow. tazpanel and browser takes forever to load and scroll within.
Everything else in the GUI is slow as well, like pcfm, sysinfo.
I fairly certain I have the correct graphics driver installed for my SiS 620 chip.
I'm going to try to attach the sys-report.html. If I cannot attach it I'll paste it here. (resolv.conf is edited to not show address in the forum)
===================================================================================
SliTaz system report
Date: Mon Mar 4 13:39:27 UTC 2013
uptime : 13:39:27 up 3 min, load average: 2.25, 2.05, 0.92
cmdline : root=/dev/hda5
version : 4.0
packages : 241 installed
kernel : 2.6.37-slitaz
free
total used free shared buffers
Mem: 245844 92356 153488 0 6280
-/+ buffers: 86076 159768
Swap: 265036 0 265036
lspci -k
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 620 Host (rev 02)
Kernel driver in use: agpgart-sis
Kernel modules: sis-agp
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step)
Kernel driver in use: SIS_IDE
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge) (rev b1)
00:01.1 Unassigned class [ff00]: Silicon Integrated Systems [SiS] ACPI
00:01.2 USB controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 11)
Kernel driver in use: ohci_hcd
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] AGP Port (virtual PCI-to-PCI bridge)
00:09.0 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50)
Subsystem: First International Computer, Inc. VA-502 Mainboard
Kernel driver in use: uhci_hcd
00:09.1 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 50)
Subsystem: First International Computer, Inc. VA-502 Mainboard
Kernel driver in use: uhci_hcd
00:09.2 USB controller: VIA Technologies, Inc. USB 2.0 (rev 51)
Subsystem: First International Computer, Inc. Device 1234
Kernel driver in use: ehci_hcd
00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Kernel driver in use: C-Media PCI
Kernel modules: snd-cmipci
00:10.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 10)
Subsystem: Davicom Semiconductor, Inc. DM9102A (DM9102AE, SM9102AF) Ethernet 100/10 MBit
Kernel driver in use: dmfe
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 530/620 PCI/AGP VGA Display Adapter (rev 2a)
Subsystem: Silicon Integrated Systems [SiS] 530/620 PCI/AGP VGA Display Adapter
lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0001
Bus 003 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001
Bus 003 Device 002: ID 062a:0001
lsmod
Module Size Used by Not tainted
snd_cmipci 22448 1
gameport 5761 1 snd_cmipci
snd_pcm 43737 1 snd_cmipci
snd_page_alloc 4853 1 snd_pcm
snd_opl3_lib 5798 1 snd_cmipci
snd_timer 12515 2 snd_pcm,snd_opl3_lib
snd_hwdep 3808 1 snd_opl3_lib
snd_mpu401_uart 3975 1 snd_cmipci
snd_rawmidi 12384 1 snd_mpu401_uart
snd_seq_device 3757 2 snd_opl3_lib,snd_rawmidi
snd 33394 10 snd_cmipci,snd_pcm,snd_opl3_lib,snd_timer,snd_hwdep,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 3357 1 snd
sis_agp 2997 1
agpgart 18221 1 sis_agp
ifconfig -a
dummy0 Link encap:Ethernet HWaddr B2:05:0B:64:2F:9E
BROADCAST NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 00:D0:09:05:C8:AD
inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1441 (1.4 KiB) TX bytes:772 (772.0 B)
Interrupt:9 Base address:0xd800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:275 errors:0 dropped:0 overruns:0 frame:0
TX packets:275 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:50518 (49.3 KiB) TX bytes:50518 (49.3 KiB)
route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
/etc/resolv.conf
search xxxxxxxxxx.net
nameserver xx.xx.xx.xx
nameserver xx.xx.xx.xx
blkid
/dev/hda1: LABEL="WIN98" UUID="241F-12E1" TYPE="vfat"
/dev/hda5: UUID="6ea0fb8d-562b-4124-8d04-e27e43adfa8f" TYPE="ext3"
/dev/hda6: TYPE="swap"
/dev/hda7: UUID="b7aa6ffe-7dc9-416a-bc14-dbbf0da9c0ed" TYPE="ext2"
/dev/hda8: UUID="b3cab562-d3a3-40bb-9fa1-ae40a0ece423" TYPE="ext2"
/dev/hda9: UUID="8d7df165-b282-4a08-b3d6-0fba76cd3594" SEC_TYPE="ext2" TYPE="ext3"
fdisk -l
Disk /dev/hda: 20.5 GB, 20525137920 bytes
255 heads, 63 sectors/track, 2495 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 593 4763241 b Win95 FAT32
/dev/hda2 594 2495 15277815 f Win95 Ext'd (LBA)
/dev/hda5 594 1213 4980118+ 83 Linux
/dev/hda6 1214 1246 265041 82 Linux swap
/dev/hda7 1772 2157 3100513+ 83 Linux
/dev/hda8 2158 2495 2714953+ 83 Linux
/dev/hda9 1247 1771 4217031 83 Linux
Partition table entries are not in disk order
mount
rootfs on / type rootfs (rw)
/dev/root on / type ext2 (rw,relatime,barrier=1,data=ordered)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /dev/shm type tmpfs (rw,relatime)
usbfs on /proc/bus/usb type usbfs (rw,relatime)
fusectl on /sys/fs/fuse/connections type fusectl (rw,relatime)
df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 4.7G 286.2M 4.2G 6% /
tmpfs 120.0M 0 120.0M 0% /dev/shm
df -i
Filesystem Inodes Used Available Use% Mounted on
/dev/root 311296 8776 302520 3% /
tmpfs 30730 1 30729 0% /dev/shm
Kernel messages
Linux version 2.6.37-slitaz (root@tank) (gcc version 4.5.2 (SliTaz) ) #2 SMP Wed Mar 7 10:36:39 CET 2012
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f800000 (usable)
BIOS-e820: 00000000ffef0000 - 00000000fff00000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.2 present.
DMI: M748LMRT /M748LMRT , BIOS 62710 07/15/97
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0xf800 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 000000000 mask FF8000000 write-back
1 base 008000000 mask FFC000000 write-back
2 base 00C000000 mask FFE000000 write-back
3 base 00E000000 mask FFF000000 write-back
4 base 00F000000 mask FFF800000 write-back
5 disabled
6 disabled
7 disabled
PAT not supported by CPU.
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-000000000f800000
0000000000 - 0000400000 page 4k
0000400000 - 000f800000 page 2M
kernel direct mapping tables up to f800000 @ 17fc000-1800000
ACPI Error: A valid RSDP was not found (20101013/tbxfroot-219)
0MB HIGHMEM available.
248MB LOWMEM available.
mapped low ram: 0 - 0f800000
low ram: 0 - 0f800000
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x0000f800
HighMem empty
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0000f800
On node 0 totalpages: 63375
free_area_init_node: node 0, pgdat c1500ec0, node_mem_map cf60f200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 464 pages used for memmap
Normal zone: 58928 pages, LIFO batch:15
Using APIC driver default
SMP: Allowing 1 CPUs, 0 hotplug CPUs
Local APIC disabled by BIOS -- you can enable it with "lapic"
APIC: disable apic facility
APIC: switched to apic NOOP
nr_irqs_gsi: 16
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at f800000 (gap: f800000:f06f0000)
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Embedded 12 pages/cpu @cf000000 s26368 r0 d22784 u4194304
pcpu-alloc: s26368 r0 d22784 u4194304 alloc=1*4194304
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62879
Kernel command line: root=/dev/hda5
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Initializing CPU#0
Initializing HighMem for node 0 (00000000:00000000)
Memory: 245408k/253952k available (3563k kernel code, 8092k reserved, 1584k data, 408k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff15000 - 0xfffff000 ( 936 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xd0000000 - 0xff7fe000 ( 759 MB)
lowmem : 0xc0000000 - 0xcf800000 ( 248 MB)
.init : 0xc1507000 - 0xc156d000 ( 408 kB)
.data : 0xc137ad15 - 0xc1506d78 (1584 kB)
.text : 0xc1000000 - 0xc137ad15 (3563 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
NR_IRQS:512
CPU 0 irqstacks, hard=cec06000 soft=cec08000
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 601.459 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 1202.91 BogoMIPS (lpj=601459)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
mce: CPU supports 5 MCE banks
Performance Events:
no APIC, boot with the "lapic" boot parameter to force-enable it.
no hardware sampling interrupt available.
p6 PMU driver.
... version: 0
... bit width: 32
... generic registers: 2
... value mask: 00000000ffffffff
... max period: 000000007fffffff
... fixed-purpose events: 0
... event mask: 0000000000000003
Checking for popad bug... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 28k freed
weird, boot CPU (#0) not listed by the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (1202.91 BogoMIPS).
devtmpfs: initialized
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab at 0
ACPI: Interpreter disabled.
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
pci 0000:00:00.0: [1039:0620] type 0 class 0x000600
pci 0000:00:00.0: reg 10: [mem 0xe8000000-0xebffffff]
pci 0000:00:00.1: [1039:5513] type 0 class 0x000101
pci 0000:00:00.1: reg 10: [io 0x01f0-0x01f7]
pci 0000:00:00.1: reg 14: [io 0x03f4-0x03f7]
pci 0000:00:00.1: reg 18: [io 0x0170-0x0177]
pci 0000:00:00.1: reg 1c: [io 0x0374-0x0377]
pci 0000:00:00.1: reg 20: [io 0xffa0-0xffaf]
pci 0000:00:01.0: [1039:0008] type 0 class 0x000601
pci 0000:00:01.1: [1039:0009] type 0 class 0x00ff00
pci 0000:00:01.2: [1039:7001] type 0 class 0x000c03
pci 0000:00:01.2: reg 10: [mem 0xefffb000-0xefffbfff]
pci 0000:00:02.0: [1039:0001] type 1 class 0x000604
pci 0000:00:09.0: [1106:3038] type 0 class 0x000c03
pci 0000:00:09.0: reg 20: [io 0xdc00-0xdc1f]
pci 0000:00:09.1: [1106:3038] type 0 class 0x000c03
pci 0000:00:09.1: reg 20: [io 0xde00-0xde1f]
pci 0000:00:09.2: [1106:3104] type 0 class 0x000c03
pci 0000:00:09.2: reg 10: [mem 0xefffaf00-0xefffafff]
pci 0000:00:09.2: PME# supported from D0 D3hot
pci 0000:00:09.2: PME# disabled
pci 0000:00:0f.0: [13f6:0111] type 0 class 0x000401
pci 0000:00:0f.0: reg 10: [io 0xda00-0xdaff]
pci 0000:00:0f.0: supports D1 D2
pci 0000:00:10.0: [1282:9102] type 0 class 0x000200
pci 0000:00:10.0: reg 10: [io 0xd800-0xd87f]
pci 0000:00:10.0: reg 14: [mem 0xefffae80-0xefffaeff]
pci 0000:00:10.0: reg 30: [mem 0xeff80000-0xeffbffff pref]
pci 0000:00:10.0: PME# supported from D3hot D3cold
pci 0000:00:10.0: PME# disabled
pci 0000:01:00.0: [1039:6306] type 0 class 0x000300
pci 0000:01:00.0: reg 10: [mem 0xe7000000-0xe77fffff pref]
pci 0000:01:00.0: reg 14: [mem 0xe7ef0000-0xe7efffff]
pci 0000:01:00.0: reg 18: [io 0xbc00-0xbc7f]
pci 0000:01:00.0: supports D2
pci 0000:00:02.0: PCI bridge to [bus 01-01]
pci 0000:00:02.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:02.0: bridge window [mem 0xe7e00000-0xe7efffff]
pci 0000:00:02.0: bridge window [mem 0xe6c00000-0xe7cfffff pref]
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
pci 0000:00:01.0: SIS IRQ router [1039:0008]
PCI: pci_cache_line_size set to 32 bytes
reserve RAM buffer: 000000000009fc00 - 000000000009ffff
reserve RAM buffer: 000000000f800000 - 000000000fffffff
Switching to clocksource tsc
pnp: PnP ACPI: disabled
pci 0000:00:02.0: PCI bridge to [bus 01-01]
pci 0000:00:02.0: bridge window [io 0xb000-0xbfff]
pci 0000:00:02.0: bridge window [mem 0xe7e00000-0xe7efffff]
pci 0000:00:02.0: bridge window [mem 0xe6c00000-0xe7cfffff pref]
pci 0000:00:02.0: setting latency timer to 64
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0xb000-0xbfff]
pci_bus 0000:01: resource 1 [mem 0xe7e00000-0xe7efffff]
pci_bus 0000:01: resource 2 [mem 0xe6c00000-0xe7cfffff pref]
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:01:00.0: Boot video device
PCI: CLS 32 bytes, default 32
platform rtc_cmos: registered platform RTC device (no PNP device found)
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.15)
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 479
io scheduler noop registered
io scheduler deadline registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Non-volatile memory driver v1.3
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
sis5513 0000:00:00.1: SiS620 ATA 66 controller
sis5513 0000:00:00.1: IDE controller (0x1039:0x5513 rev 0xd0)
sis5513 0000:00:00.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7
ide1: BM-DMA at 0xffa8-0xffaf
Probing IDE interface ide0...
hda: WDC WD205BA, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: host side 80-wire cable detection failed, limiting max speed to UDMA33
hda: UDMA/33 mode selected
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-M1402, ATAPI CD/DVD-ROM drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
ide-gd driver 1.18
hda: max request size: 128KiB
hda: 40088160 sectors (20525 MB) w/2048KiB Cache, CHS=39770/16/63
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
ide-cd driver 5.00
ide-cd: hdc: ATAPI 40X DVD-ROM drive, 128kB Cache
cdrom: Uniform CD-ROM driver Revision: 3.20
e1000e: Intel(R) PRO/1000 Network Driver - 1.2.7-k2
e1000e: Copyright (c) 1999 - 2010 Intel Corporation.
pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ThunderLAN driver v1.15a
TLAN: 0 devices installed, PCI: 0 EISA: 0
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
PCI: setting IRQ 9 as level-triggered
dmfe 0000:00:10.0: found PCI INT A -> IRQ 9
net eth0: Davicom DM9102 at pci0000:00:10.0, 00:d0:09:05:c8:ad, irq 9
winbond-840.c:v1.01-e (2.4 port) Sep-11-2006 Donald Becker
http://www.scyld.com/network/drivers.html
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: setting IRQ 10 as level-triggered
ehci_hcd 0000:00:09.2: found PCI INT C -> IRQ 10
ehci_hcd 0000:00:09.2: EHCI Host Controller
ehci_hcd 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:09.2: irq 10, io mem 0xefffaf00
ehci_hcd 0000:00:09.2: USB 2.0 started, EHCI 0.95
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:01.2: OHCI Host Controller
ohci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:01.2: irq 3, io mem 0xefffb000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
PCI: setting IRQ 12 as level-triggered
uhci_hcd 0000:00:09.0: found PCI INT A -> IRQ 12
uhci_hcd 0000:00:09.0: UHCI Host Controller
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:09.0: irq 12, io base 0x0000dc00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: setting IRQ 11 as level-triggered
uhci_hcd 0000:00:09.1: found PCI INT B -> IRQ 11
uhci_hcd 0000:00:09.1: sharing IRQ 11 with 0000:00:0f.0
uhci_hcd 0000:00:09.1: UHCI Host Controller
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:09.1: irq 11, io base 0x0000de00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /devices/platform/pcspkr/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI No-Shortcut mode
EXT4-fs (hda5): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext2 filesystem) readonly on device 3:5.
Freeing unused kernel memory: 408k freed
usb 3-1: new low speed USB device using uhci_hcd and address 2
input: HID 062a:0001 as /devices/pci0000:00/0000:00:09.0/usb3/3-1/3-1:1.0/input/input2
generic-usb 0003:062A:0001.0001: input: USB HID v1.10 Mouse [HID 062a:0001] on usb-0000:00:09.0-1/input0
EXT4-fs (hda5): re-mounted. Opts: barrier=1,data=ordered
EXT4-fs (hda5): re-mounted. Opts: barrier=1,data=ordered
<30>udevd[588]: starting version 170
Boot scripts
Processing /etc/init.d/rcS...
Mounting proc filesystem... [ OK ]
Checking filesystem on : /dev/hda5
/dev/hda5: clean, 8768/311296 files, 92805/1245029 blocks
Remounting rootfs read/write...
Starting udev daemon...
Udevadm requesting events from the Kernel...
Udevadm waiting for the event queue to finish...
Using Udev for hotplugging...
Mounting filesystems in fstab...
Searching for early boot options... [ OK ]
Cleaning up the system... [ OK ]
Setting up tmp X11 and ICE unix dir... [ OK ]
Chmoding cdrom device... [ OK ]
Mounting /proc/bus/usb filesystem... [ OK ]
Starting system log deamon: syslogd... [ OK ]
Starting kernel log daemon: klogd... [ OK ]
Requesting events from the Kernel... [ OK ]
Executing all initialization scripts...
Parsing kernel cmdline for SliTaz live options...
Swap memory detected on: /dev/hda6
Activating swap memory...
Setting hostname... [ OK ]
Configuring loopback... [ OK ]
Starting udhcpc client on: eth0...
udhcpc (v1.18.4) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
Restoring last alsa configuration... [ OK ]
Starting TazPanel web server on port 82... [ OK ]
Checking if /etc/locale.conf exists...
Locale configuration: en_US [ OK ]
Keymap configuration: us
Loading /usr/share/kbd/keymaps/i386/qwerty/us.map.gz
Starting local startup commands...
Starting all daemons specified in /etc/rcS.conf...
Starting message bus daemon: DBUS... [ OK ]
Starting Hardware Abstraction Layer: HAL... [ OK ]
Starting slim login manager: Slim... [ OK ]
Setting up kernel security rules... [ OK ]
Iptables rules are disabled in: /etc/firewall.conf...
Starting httpd deamon: httpd... [ OK ]
Welcome to your box.
SliTaz boot time: 46s