Does someone knows how to install rt3090 in Slitaz?
Tanks
Does someone knows how to install rt3090 in Slitaz?
Tanks
Had you try that package ?
firmware-rt2x00
"Recette" of it shows it should work :
PROVIDE="firmware-rt73 firmware-rt2561 firmware-rt2661 firmware-rt2860 \
firmware-rt2870 firmware-rt3070 firmware-rt3071 firmware-rt3090"
It didn't work :(
Type each command in terminal,hit the Enter key,post the output in your reply.
lspci -nn
lsusb
uname -a
ls /sys/class/net
iwconfig
iwlist scan
ifconfig
lsmod
lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller [8086:0044] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0046] (rev 02)
00:16.0 Communication controller [0780]: Intel Corporation 5 Series/3400 Series Chipset HECI Controller [8086:3b64] (rev 06)
00:1a.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 05)
00:1b.0 Audio device [0403]: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio [8086:3b56] (rev 05)
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 [8086:3b42] (rev 05)
00:1c.1 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 [8086:3b44] (rev 05)
00:1c.2 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 [8086:3b46] (rev 05)
00:1d.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 05)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev a5)
00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller [8086:3b09] (rev 05)
00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller [8086:3b29] (rev 05)
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 05)
00:1f.6 Signal processing controller [1180]: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem [8086:3b32] (rev 05)
04:00.0 Network controller [0280]: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe [1814:3090]
06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
ff:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers [8086:2c62] (rev 02)
ff:00.1 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture System Address Decoder [8086:2d01] (rev 02)
ff:02.0 Host bridge [0600]: Intel Corporation Core Processor QPI Link 0 [8086:2d10] (rev 02)
ff:02.1 Host bridge [0600]: Intel Corporation Core Processor QPI Physical 0 [8086:2d11] (rev 02)
ff:02.2 Host bridge [0600]: Intel Corporation Core Processor Reserved [8086:2d12] (rev 02)
ff:02.3 Host bridge [0600]: Intel Corporation Core Processor Reserved [8086:2d13] (rev 02)
lsusb:
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 001 Device 002: ID 8087:0020
Bus 002 Device 002: ID 8087:0020
Bus 002 Device 003: ID 0ac8:3630
Bus 002 Device 004: ID 0a12:0001
Bus 002 Device 005: ID 048d:1336
uname -a:
Linux slitaz 2.6.37-slitaz #2 SMP Thu May 16 19:27:13 CEST 2013 i686 GNU/Linux
ls /sys/class/net:
dummy0 eth0 lo wlan0
iwconfig:
lo no wireless extensions.
dummy0 no wireless extensions.
eth0 no wireless extensions.
wlan0 Ralink STA ESSID:"dlink" Nickname:"RT2860STA"
Mode:Managed Frequency=2.412 GHz Access Point: 00:22:B0:47:84:85
Bit Rate=36 Mb/s
RTS thr:off Fragment thr:off
Link Quality=100/100 Signal level:-37 dBm Noise level:-83 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
iwlist scan:
lo no wireless extensions.
dummy0 no wireless extensions.
eth0 no wireless extensions.
wlan0 Ralink STA ESSID:"dlink" Nickname:"RT2860STA"
Mode:Managed Frequency=2.412 GHz Access Point: 00:22:B0:47:84:85
Bit Rate=36 Mb/s
RTS thr:off Fragment thr:off
Link Quality=100/100 Signal level:-37 dBm Noise level:-83 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
ifconfig:
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1410 errors:0 dropped:0 overruns:0 frame:0
TX packets:1410 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:249708 (243.8 KiB) TX bytes:249708 (243.8 KiB)
wlan0 Link encap:Ethernet HWaddr 00:02:72:A1:D9:92
inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:31952 errors:0 dropped:0 overruns:0 frame:0
TX packets:20423 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:42336570 (40.3 MiB) TX bytes:2254241 (2.1 MiB)
Interrupt:17
lsmod:
Module Size Used by Tainted: G
rt2860sta 388448 1
snd_hda_codec_hdmi 16401 1
snd_hda_codec_realtek 202176 1
snd_hda_intel 15886 1
snd_hda_codec 45027 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 3808 1 snd_hda_codec
snd_pcm 43737 2 snd_hda_intel,snd_hda_codec
snd_timer 12515 1 snd_pcm
snd 33394 9 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
soundcore 3357 1 snd
snd_page_alloc 4853 2 snd_hda_intel,snd_pcm
i915 254040 2
drm_kms_helper 18798 1 i915
drm 111992 3 i915,drm_kms_helper
i2c_algo_bit 3479 1 i915
button 3602 1 i915
i2c_core 12192 4 i915,drm_kms_helper,drm,i2c_algo_bit
video 9783 1 i915
output 1144 1 video
intel_agp 7908 1 i915
intel_gtt 9214 3 i915,intel_agp
agpgart 18221 3 drm,intel_agp,intel_gtt
the wireless is working right now because i'm near the signal......but in the next room it doesn't work
I removed rt2860sta from loading at boot and did rt2x00pci to load.....but the wireless didn't work
no more ideas?
please someone
You must log in to post.