SliTaz Forum

Wireless in Slitaz 4.0

(6 posts) (2 voices)

• Started 11 years ago by Anand
• Latest reply from mojo
• This topic is not a support question

Tags:

No tags yet.

1. 

   Anand
   

   offline

   Member

   Hi there
   I am impressed with Slitaz but unfortunately cannot get the wireless working. I don't have ethernet to test wired. Is there any help for me please.

   The driver I am looking for is BCM4311 chipset id 14e4:4319 (rev 2)Dell Latitude D610.
   the windows device manager says the name is this: Dell Wireless 1470Dual Band WLAN Mini-PCI Card.

   Any help would be greatly appreciated. Cheers

   Posted 11 years ago #
2. 

   mojo
   

   offline

   Key Master

   Download: http://people.slitaz.org/~mojo/stuff/b43-firmware-4.150.10.5.tazpkg
   Copy to flash drive move to SliTaz 4.0
   Open terminal,su ,password: root
   tazpkg install b43-firmware-4.150.10.5.tazpkg
modprobe -r b43 ; modprobe b43
   Applications/System Tools/Wifi configuration
   Password: root , click OK button
   Dbl click WAP to connect, or enter WPA Password: click OK if secure to connect.

   Posted 11 years ago #
3. 

   Anand
   

   offline

   Member

   Thank you mojo
   Did as per your instructions, unfortunately I have blank wifi connections detected to double click. The wifi configuration table is empty. I try to connect by feeding the encryption key and type and tried to configure but still could not find network. Can you help me. Thank you.

   Posted 11 years ago #
4. 

   mojo
   

   offline

   Key Master

   It seems that your wifi adapters radio is not switched on.
   Forgot to mention to set the wireless router to broadcast a ESSID name or you can't connect.
   Reviewed my instructions on a 2006 Dell Inspiron E1505 laptop which has BCM4311 wireless.
   I found it was not necessary to modprobe -r b43 ; modprobe b43
   Install the firmware,open Wifi configuration which opens Wifi network box.
   A couple of seconds later the computers wifi indicator lights up and the wireless access point ESSID name appears under any.
   Dbl clicked my access points essid name,which opens Wifi connection box.
   Enter the WPA password, click OK button and it connects.

   Check the firmware md5sum matches mine:
   tux@slitaz:~$ md5sum b43-firmware-4.150.10.5.tazpkg
   bee851150681f04ad914aad3d1fb444f b43-firmware-4.150.10.5.tazpkg
   Run the command in bold after installing firmware and opening Wifi configuration.
   You should see similar output:
   tux@slitaz:~$ dmesg | grep -i b43
   b43-pci-bridge 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
   b43-pci-bridge 0000:0b:00.0: setting latency timer to 64
   b43-phy0: Broadcom 4311 WLAN found (core revision 10)
   Registered led device: b43-phy0::tx
   Registered led device: b43-phy0::rx
   Registered led device: b43-phy0::radio
   b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
   b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)

   Posted 11 years ago #
5. 

   Anand
   

   offline

   Member

   Hi mojo

   Thank you very much. I tried on virtualbox of other machine Dell D505 too with no match from dmesg |grep -i b43. however this has Intel Pro/Wireless 2200BG. I will retry on actual machine once I get my hand to it. Meanwhile please can you help me know how to do the following. "To set the wireless router to broadcast a ESSID name or you can't connect." Thank you very much.

   Posted 11 years ago #
6. 

   mojo
   

   offline

   Key Master

   Read the directions that come with the wireless router.

   Posted 11 years ago #

RSS feed for this topic

Reply

You must log in to post.