Hola

ggg · 2014-03-01 14:19:02

Hola, estoy tratando de instalar slitaz en una partición con AlphaOS Linux ya instalado. Lo hago iniciando desde un pendrive, pero no detecta los discos duros, así que no puedo copiar los archivos del pendrive al disco duro para hacer una instalación en un subdirectorio. Alguien sabe como me puede ayudar?

Desde ya muchas gracias

ggg · 2014-03-01 14:23:28

This is the English translation, if anyone can help me in that language, thanks

Hello, I am trying to install slitaz on a partition with Linux already installed AlphaOS. I do this by booting from a USB flash drive, but does not detect the hard drives, so I can not copy files from pendrive to hard disk for installation in a subdirectory. Anyone know how I can help?

From already thank you very much

mojo · 2014-03-01 14:35:52

Boot into slitaz on flash drive.

Open a terminal.

Type this command:

[c]lspci -vvnn[/c]

Hit the Enter key

Post the output from the command in your next post.

ggg · 2014-03-01 15:24:34

tux@slitaz:~$ lspci -vvnn

00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:0364]

Subsystem: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:0364]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

Latency: 8

Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]

Capabilities: <access denied>

Kernel driver in use: agpgart-via

00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:1364]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0

00:00.2 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:2364]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0

00:00.3 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:3364]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0

00:00.4 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:4364]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0

00:00.5 PIC [0800]: VIA Technologies, Inc. CN896/VN896/P4M900 I/O APIC Interrupt Controller [1106:5364] (prog-if 20 [IO(X)-APIC])

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0, Cache Line Size: 64 bytes

00:00.6 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Security Device [1106:6364]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0, Cache Line Size: 64 bytes

00:00.7 Host bridge [0600]: VIA Technologies, Inc. CN896/VN896/P4M900 Host Bridge [1106:7364]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0

00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0, Cache Line Size: 64 bytes

Bus: primary=00, secondary=01, subordinate=01, sec-latency=0

I/O behind bridge: 0000c000-0000cfff

Memory behind bridge: fb000000-fcffffff

Prefetchable memory behind bridge: d0000000-d7ffffff

Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-

BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: <access denied>

00:02.0 PCI bridge [0604]: VIA Technologies, Inc. CN896/VN896/P4M900 PCI to PCI Bridge Controller [1106:a364] (rev 80) (prog-if 00 [Normal decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0, Cache Line Size: 64 bytes

Bus: primary=00, secondary=02, subordinate=02, sec-latency=0

I/O behind bridge: 0000b000-0000bfff

Memory behind bridge: fdc00000-fdcfffff

Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff

Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-

BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: <access denied>

Kernel driver in use: pcieport

00:03.0 PCI bridge [0604]: VIA Technologies, Inc. CN896/VN896/P4M900 PCI to PCI Bridge Controller [1106:c364] (rev 80) (prog-if 00 [Normal decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0, Cache Line Size: 64 bytes

Bus: primary=00, secondary=03, subordinate=03, sec-latency=0

I/O behind bridge: 0000a000-0000afff

Memory behind bridge: fde00000-fdefffff

Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff

Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-

BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: <access denied>

Kernel driver in use: pcieport

00:0f.0 IDE interface [0101]: VIA Technologies, Inc. Device [1106:5337] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])

Subsystem: Biostar Microtech Int'l Corp Device [1565:5300]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32

Interrupt: pin B routed to IRQ 11

Region 0: I/O ports at fc00 [size=8]

Region 1: I/O ports at f800 [size=4]

Region 2: I/O ports at f400 [size=8]

Region 3: I/O ports at f000 [size=4]

Region 4: I/O ports at ec00 [size=16]

Region 5: I/O ports at e800 [size=256]

Capabilities: <access denied>

00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 07) (prog-if 8a [Master SecP PriP])

Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE [1106:0571]

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32

Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]

Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)

Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]

Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)

Region 4: I/O ports at e400 [size=16]

Capabilities: <access denied>

00:10.0 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])

Subsystem: Biostar Microtech Int'l Corp Device [1565:3206]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32, Cache Line Size: 64 bytes

Interrupt: pin A routed to IRQ 20

Region 4: I/O ports at e000 [size=32]

Capabilities: <access denied>

Kernel driver in use: uhci_hcd

00:10.1 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])

Subsystem: Biostar Microtech Int'l Corp Device [1565:3206]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32, Cache Line Size: 64 bytes

Interrupt: pin B routed to IRQ 22

Region 4: I/O ports at dc00 [size=32]

Capabilities: <access denied>

Kernel driver in use: uhci_hcd

00:10.2 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])

Subsystem: Biostar Microtech Int'l Corp Device [1565:3206]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32, Cache Line Size: 64 bytes

Interrupt: pin C routed to IRQ 21

Region 4: I/O ports at d800 [size=32]

Capabilities: <access denied>

Kernel driver in use: uhci_hcd

00:10.3 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev a0) (prog-if 00 [UHCI])

Subsystem: Biostar Microtech Int'l Corp Device [1565:3206]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32, Cache Line Size: 64 bytes

Interrupt: pin D routed to IRQ 23

Region 4: I/O ports at d400 [size=32]

Capabilities: <access denied>

Kernel driver in use: uhci_hcd

00:10.4 USB controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI])

Subsystem: Biostar Microtech Int'l Corp Device [1565:3206]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32, Cache Line Size: 64 bytes

Interrupt: pin C routed to IRQ 21

Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=256]

Capabilities: <access denied>

Kernel driver in use: ehci_hcd

00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237A PCI to ISA Bridge [1106:3337]

Subsystem: Biostar Microtech Int'l Corp Device [1565:3206]

Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Capabilities: <access denied>

00:11.7 Host bridge [0600]: VIA Technologies, Inc. VT8237/8251 Ultra VLINK Controller [1106:287e]

Subsystem: VIA Technologies, Inc. Device [1106:337e]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

Latency: 32

Capabilities: <access denied>

00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 7c)

Subsystem: Biostar Microtech Int'l Corp Device [1565:2200]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32 (750ns min, 2000ns max), Cache Line Size: 64 bytes

Interrupt: pin A routed to IRQ 23

Region 0: I/O ports at d000 [size=256]

Region 1: Memory at fdffe000 (32-bit, non-prefetchable) [size=256]

Capabilities: <access denied>

Kernel driver in use: via-rhine

00:13.0 Host bridge [0600]: VIA Technologies, Inc. VT8237A Host Bridge [1106:337b]

Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

00:13.1 PCI bridge [0604]: VIA Technologies, Inc. VT8237A PCI to PCI Bridge [1106:337a] (prog-if 01 [Subtractive decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-

Latency: 0

Bus: primary=00, secondary=04, subordinate=04, sec-latency=0

I/O behind bridge: 00009000-00009fff

Memory behind bridge: fda00000-fdafffff

Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff

Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-

BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: <access denied>

01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. CN896/VN896/P4M900 [Chrome 9 HC] [1106:3371] (rev 01) (prog-if 00 [VGA controller])

Subsystem: Biostar Microtech Int'l Corp Device [1565:1207]

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 32 (500ns min)

Interrupt: pin A routed to IRQ 11

Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]

Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]

[virtual] Expansion ROM at fc000000 [disabled] [size=64K]

Capabilities: <access denied>

04:04.0 Modem [0703]: SILICON Laboratories Intel 537 [Winmodem] [1543:3052] (rev 04) (prog-if 00 [Generic])

Subsystem: SILICON Laboratories Device [1543:3000]

Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Interrupt: pin A routed to IRQ 17

Region 0: Memory at fdaff000 (32-bit, non-prefetchable) [size=4K]

Region 1: I/O ports at 9c00 [size=256]

Capabilities: <access denied>

80:01.0 Audio device [0403]: VIA Technologies, Inc. VT8237A/VT8251 HDA Controller [1106:3288] (rev 10)

Subsystem: Biostar Microtech Int'l Corp Device [1565:820d]

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-

Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

Latency: 0, Cache Line Size: 64 bytes

Interrupt: pin A routed to IRQ 17

Region 0: Memory at cfffc000 (64-bit, non-prefetchable) [size=16K]

Capabilities: <access denied>

Kernel driver in use: snd_hda_intel

tux@slitaz:~$

mojo · 2014-03-01 15:54:26

IDE controller connects the motherboard to the hard drives.

Your motherboard requires [c]sata_via.ko.xz[/c] and [c]pata_via.ko.xz[/c] for the IDE controller to work.

See if they are installed:

login as root.

[c]tazpkg search-file sata_via.ko.xz[/c]

Hit Enter

[c]tazpkg search-file pata_via.ko.xz[/c]

Hit Enter

They should be in the linux tazpkg.

ggg · 2014-03-01 16:13:38

tux@slitaz:~$ su

Password:

root@slitaz:/home/tux# tazpkg search-file sata_via.ko.xz

Resultado de búsqueda para archivo sata_via.ko.xz

================================================================================

0 filas encontradas para: sata_via.ko.xz

root@slitaz:/home/tux# tazpkg search-file pata_via.ko.xz

Resultado de búsqueda para archivo pata_via.ko.xz

================================================================================

0 filas encontradas para: pata_via.ko.xz

root@slitaz:/home/tux#

They should be in the linux tazpkg. (Is not)

ggg · 2014-03-01 16:34:06

tux@slitaz:~$ tazpkg search-file pata_via.ko.xz

Resultado de búsqueda para archivo pata_via.ko.xz

================================================================================

Paquete linux:

/lib/modules/3.2.53-slitaz/kernel/drivers/ata/pata_via.ko.xz

================================================================================

1 file found for: pata_via.ko.xz

tux@slitaz:~$

tux@slitaz:~$ tazpkg search-file sata_via.ko.xz

Resultado de búsqueda para archivo sata_via.ko.xz

================================================================================

Paquete linux:

/lib/modules/3.2.53-slitaz/kernel/drivers/ata/sata_via.ko.xz

================================================================================

1 file found for: sata_via.ko.xz

tux@slitaz:~$

And Now?

mojo · 2014-03-01 16:39:16

The cooking release was made with linux tazpkg missing many drivers.

The linux tazpkg has been fixed.

Boot into AlphaOS and use it to install Slitaz.

Extract the slitaz file tree from rootfs.gz into the sub folder

Chroot into the Slitaz filesystem sub folder.

While connected to the internet.

[c]tazpkg recharge[/c]

[c]tazpkg -gi linux --force[/c]

Edit:

Forget the chroot with AlphaOS.

AlphaOS is 64 bit and Slitaz is 32 bit,it will not work.

Download/install the http://mirror.slitaz.org/iso/rolling/slitaz-rolling-iso

ggg · 2014-03-01 16:49:16

It's too complicated for me, I need you to tell me how are the commands

ggg · 2014-03-01 16:58:00

Extract the slitaz file tree from rootfs.gz into the sub folder

Chroot into the Slitaz filesystem sub folder.

I dont know how.

mojo · 2014-03-01 17:04:44

Forget chroot with AlphaOS.

AlphaOS is 64 bit and Slitaz is 32 bit,it will not work.

Download/install the fixed iso to the USB flash drive:

http://mirror.slitaz.org/iso/rolling/slitaz-rolling-iso

ggg · 2014-03-01 17:44:45

OK, and now? PArtitions in hard drive still not appears

mojo · 2014-03-01 18:00:55

[c]tazpkg search-file sata_via.ko.xz[/c]

Hit Enter

[c]tazpkg search-file pata_via.ko.xz[/c]

Hit Enter

Post output of [c]lsmod[/c]

ggg · 2014-03-01 18:48:16

tux@slitaz:~$ tazpkg search-file sata_via.ko.xz

Resultado de búsqueda para archivo sata_via.ko.xz

================================================================================

Paquete linux:

/lib/modules/3.2.53-slitaz/kernel/drivers/ata/sata_via.ko.xz

================================================================================

1 file found for: sata_via.ko.xz

tux@slitaz:~$ lsmod

Module Size Used by Not tainted

ata_generic 2135 0

pata_acpi 1964 0

ipv6 178458 17

ppdev 4062 0

snd_hda_codec_realtek 134559 1

snd_hda_intel 16713 0

snd_hda_codec 45592 2 snd_hda_codec_realtek,snd_hda_intel

snd_usb_audio 63217 1

floppy 40432 0

pata_via 6413 0

sata_via 5084 0

parport_pc 14553 0

via_agp 4479 1

agpgart 17571 1 via_agp

parport 21099 2 ppdev,parport_pc

snd_usbmidi_lib 12273 1 snd_usb_audio

button 3286 0

snd_hwdep 3811 2 snd_hda_codec,snd_usb_audio

snd_rawmidi 12197 1 snd_usbmidi_lib

snd_seq_device 3476 1 snd_rawmidi

snd_pcm 42934 3 snd_hda_intel,snd_hda_codec,snd_usb_audio

snd_page_alloc 4673 2 snd_hda_intel,snd_pcm

snd_timer 12073 1 snd_pcm

snd 33335 12 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_usb_audio,snd_usbmidi_lib,snd_hwdep,snd_rawmidi,snd_seq_device,snd_pcm,snd_timer

soundcore 3258 1 snd

tux@slitaz:~$

mojo · 2014-03-01 19:18:59

Login as root:

[c]su[/c]

Password:

[c]root[/c]

Type this:

[c]parted -l[/c]

Hit Enter

Post the output.

[c]fdisk -l[/c]

Hit Enter

Post the output.

sixofeight · 2014-03-01 21:02:16

small hint

In latest rolling:

If you are logged in as tux, SpaceFm does not show internal Hdd-Partitions by default.

In SpaceFm click Devices-> settings-> show-> check "internal Drives"

ggg · 2014-03-02 13:18:08

OK, with instructions of sixofeight could see the hard drive partitions, thanks.

Now, Slitaz rolling supports 64 bits? I can proceed with the installation subdirectory normally?

Or I have to make a separate partition for Slitaz?

ggg · 2014-03-13 02:40:49

I can not see partitions, therefore I can not install.

SliTaz Forum

SliTaz Forum

#1 2014-03-01 14:19:02

Hola

#2 2014-03-01 14:23:28

Re: Hola

#3 2014-03-01 14:35:52

Re: Hola

#4 2014-03-01 15:24:34

Re: Hola

#5 2014-03-01 15:54:26

Re: Hola

#6 2014-03-01 16:13:38

Re: Hola

#7 2014-03-01 16:34:06

Re: Hola

#8 2014-03-01 16:39:16

Re: Hola

#9 2014-03-01 16:49:16

Re: Hola

#10 2014-03-01 16:58:00

Re: Hola

#11 2014-03-01 17:04:44

Re: Hola

#12 2014-03-01 17:44:45

Re: Hola

#13 2014-03-01 18:00:55

Re: Hola

#14 2014-03-01 18:48:16

Re: Hola

#15 2014-03-01 19:18:59

Re: Hola

#16 2014-03-01 21:02:16

Re: Hola

#17 2014-03-02 13:18:08

Re: Hola

#18 2014-03-13 02:40:49

Re: Hola

Board footer