SliTaz Forum
You are not logged in.
Pages: 1
live cd don't find any hard drive on my computer.
root@slitaz:/home/tux# lspci
00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 200 Host Bridge (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge
00:19.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge
00:1c.0 USB controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.1 USB controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.2 USB controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.3 USB controller: ALi Corporation USB 2.0 Controller (rev 01)
00:1d.0 Audio device: ALi Corporation High Definition Audio/AC'97 Host Controller
00:1e.0 ISA bridge: ALi Corporation PCI to LPC Controller (rev 31)
00:1e.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:1f.0 IDE interface: ALi Corporation M5229 IDE (rev c7)
00:1f.1 RAID bus controller: ALi Corporation ULi 5287 SATA (rev 02)
01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress 200]
02:15.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
root@slitaz:/home/tux# dmesg | grep -i -e ide -e hda -e sata
pci 0000:01:05.0: Boot video device
Uniform Multi-Platform E-IDE driver
alim15x3 0000:00:1f.0: IDE controller (0x10b9:0x5229 rev 0xc7)
ide0: BM-DMA at 0xff00-0xff07
ide1: BM-DMA at 0xff08-0xff0f
Probing IDE interface ide0...
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
ide-gd driver 1.18
ide-cd driver 5.00
ide-cd: hdc: ATAPI 48X DVD-ROM drive, 256kB Cache
HDA Intel 0000:00:1d.0: PCI INT C -> GSI 22 (level, low) -> IRQ 22
hda_codec: ALC880: BIOS auto-probing.
[drm] S-video
Offline
Can you atleast mention with which LiveCD (Stable/4.0, Cooking, Rolling and base, core, just-x, etc variations) you were experiencing this problem with?
Offline
sorry, with last stable cd (4.0)
Offline
Open terminal,login root,password: root
Post the output from these commands:
[c]fdisk -l[/c]
[c]parted -l[/c]
[c]blkid[/c]
[c]lsmod[/c]
[c]lspci -nnvv[/c]
Offline
root@slitaz:/home/tux# fdisk -l
root@slitaz:/home/tux#
root@slitaz:/home/tux# parted -l
Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0
has been opened read-only.
Error: /dev/sr0: unrecognised disk label
Model: HL-DT-ST DVDRAM GP30NB20 (scsi)
Disk /dev/sr0: 569MB
Sector size (logical/physical): 2048B/2048B
Partition Table: unknown
root@slitaz:/home/tux#
root@slitaz:/home/tux# blkid
root@slitaz:/home/tux#
root@slitaz:/home/tux# lsmod
Module Size Used by Not tainted
parport_pc 16061 0
floppy 41138 0
parport 20983 1 parport_pc
button 3602 0
skge 29359 0
radeon 673881 1
ttm 35361 1 radeon
drm_kms_helper 18798 1 radeon
drm 111992 3 radeon,ttm,drm_kms_helper
hwmon 993 1 radeon
i2c_algo_bit 3479 1 radeon
i2c_core 12192 4 radeon,drm_kms_helper,drm,i2c_algo_bit
snd_hda_codec_realtek 202176 1
snd_hda_intel 15886 1
snd_hda_codec 45027 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 3808 1 snd_hda_codec
snd_pcm 43737 2 snd_hda_intel,snd_hda_codec
snd_timer 12515 1 snd_pcm
snd 33394 8 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
soundcore 3357 1 snd
snd_page_alloc 4853 2 snd_hda_intel,snd_pcm
ati_agp 4010 0
agpgart 18221 3 ttm,drm,ati_agp
root@slitaz:/home/tux#
root@slitaz:/home/tux# lspci -nnvv
00:00.0 Host bridge [0600]: ATI Technologies Inc Radeon Xpress 200 Host Bridge [1002:5a33] (rev 01)
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
Kernel modules: ati-agp
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ff400000-ff4fffff
Prefetchable memory behind bridge: bff00000-dfefffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [b0] Subsystem: Elitegroup Computer Systems Device [1019:1b36]
00:19.0 PCI bridge [0604]: ALi Corporation M5249 HTT to PCI Bridge [10b9:5249] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR+ <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff500000-ff5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR+ <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [c0] HyperTransport: MSI Mapping Enable+ Fixed+
00:1c.0 USB controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at ff6ff000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:1c.1 USB controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at ff6fe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:1c.2 USB controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 19
Region 0: Memory at ff6fd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:1c.3 USB controller [0c03]: ALi Corporation USB 2.0 Controller [10b9:5239] (rev 01) (prog-if 20 [EHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 23
Region 0: Memory at ff6fcc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=0090
Kernel driver in use: ehci_hcd
00:1d.0 Audio device [0403]: ALi Corporation High Definition Audio/AC'97 Host Controller [10b9:5461]
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 20000ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ff6f8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1e.0 ISA bridge [0601]: ALi Corporation PCI to LPC Controller [10b9:1573] (rev 31)
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 6000ns max)
00:1e.1 Bridge [0680]: ALi Corporation M7101 Power Management Controller [PMU] [10b9:7101]
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:1f.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229] (rev c7) (prog-if 8a [Master SecP PriP])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 21
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at ff00 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ALI15x3_IDE
00:1f.1 RAID bus controller [0104]: ALi Corporation ULi 5287 SATA [10b9:5287] (rev 02)
Subsystem: Elitegroup Computer Systems Device [1019:5287]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 512 bytes
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at ec00 [size=16]
Region 1: I/O ports at e800 [size=8]
Region 2: I/O ports at e400 [size=16]
Region 3: I/O ports at e000 [size=8]
Region 4: I/O ports at dc00 [size=32]
Region 5: Memory at ff6fc800 (32-bit, non-prefetchable) [disabled] [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RC410 [Radeon Xpress 200] [1002:5a61] (prog-if 00 [VGA controller])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at b800 [size=256]
Region 2: Memory at ff4f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at ff4c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Kernel driver in use: radeon
Kernel modules: radeon
02:15.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller [11ab:4320] (rev 13)
Subsystem: Elitegroup Computer Systems Marvell 88E8001 Gigabit Ethernet Controller (ECS) [1019:8001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at ff5fc000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at c800 [size=256]
Expansion ROM at ff5c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=7 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
Read-only fields:
[PN] Part number: Yukon 88E8001
[EC] Engineering changes: Rev. 1.3
[MN] Manufacture ID: 4d 61 72 76 65 6c 6c
[SN] Serial number: AbCdEfG334454
[CP] Extended capability: 01 10 cc 03
[RV] Reserved: checksum good, 10 byte(s) reserved
Read/write fields:
[RW] Read-write area: 121 byte(s) free
End
Kernel driver in use: skge
Kernel modules: skge
root@slitaz:/home/tux#
Offline
Boot into a linux live cd from another distro that recognizes your hard drive and run the same commands and post the output.
Print the working distros kernel configuration to file and attach it.
I will diff the outputs and compare the kernel configurations to see what drivers are required by your hardware that are not compiled in the slitaz-4.0 kernel
Offline
on last debian, hard drive detect :
root@debian:/home/debian# fdisk -l
Disque /dev/sda : 164.7 Go, 164696555520 octets
255 têtes, 63 secteurs/piste, 20023 cylindres, total 321672960 secteurs
Unités = secteurs de 1 * 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Identifiant de disque : 0x0000e7e0
Périphérique Amorce Début Fin Blocs Id Système
/dev/sda1 * 2048 320102399 160050176 83 Linux
/dev/sda2 320104446 321671167 783361 5 Étendue
/dev/sda5 320104448 321671167 783360 82 partition d'échange Linux / Solaris
root@debian:/home/debian# parted -l
bash: parted : commande introuvable
root@debian:/home/debian# blkid
/dev/sda5: UUID="91c3f88b-020c-46f6-ae32-5aaffd3086db" TYPE="swap"
/dev/sda1: UUID="43109256-51da-43fc-918c-03b0c740b87e" TYPE="ext4"
root@debian:/home/debian# lsmod
Module Size Used by
nls_utf8 12416 0
nls_cp437 12417 0
vfat 17116 0
fat 44497 1 vfat
ext3 134152 0
jbd 47281 1 ext3
nfsd 173890 2
nfs 265921 0
nfs_acl 12463 2 nfs,nfsd
auth_rpcgss 32143 2 nfs,nfsd
fscache 31978 1 nfs
lockd 57277 2 nfs,nfsd
sunrpc 143904 6 lockd,auth_rpcgss,nfs_acl,nfs,nfsd
loop 17810 0
snd_hda_codec_realtek 142274 1
snd_hda_intel 21786 0
snd_hda_codec 63477 2 snd_hda_intel,snd_hda_codec_realtek
snd_hwdep 12943 1 snd_hda_codec
snd_pcm 53461 2 snd_hda_codec,snd_hda_intel
radeon 640791 2
snd_page_alloc 12867 2 snd_pcm,snd_hda_intel
ttm 47786 1 radeon
snd_timer 22356 1 snd_pcm
snd 42722 6 snd_timer,snd_pcm,snd_hwdep,snd_hda_codec,snd_hda_intel,snd_hda_codec_realtek
soundcore 12921 1 snd
drm_kms_helper 22738 1 radeon
drm 146387 4 drm_kms_helper,ttm,radeon
i2c_ali15x3 12490 0
i2c_ali1535 12490 0
joydev 17010 0
parport_pc 22036 0
parport 31254 1 parport_pc
evdev 17225 9
serio_raw 12803 0
pcspkr 12515 0
power_supply 13283 1 radeon
i2c_algo_bit 12713 1 radeon
i2c_core 19116 6 i2c_algo_bit,i2c_ali1535,i2c_ali15x3,drm,drm_kms_helper,radeon
processor 27565 0
button 12817 0
shpchp 26717 0
thermal_sys 17752 1 processor
ext4 306996 1
crc16 12327 1 ext4
jbd2 52330 1 ext4
mbcache 12938 2 ext4,ext3
sg 21476 0
sd_mod 35425 3
crc_t10dif 12332 1 sd_mod
sr_mod 17468 0
usbhid 31554 0
cdrom 34813 1 sr_mod
hid 64284 1 usbhid
ata_generic 12439 0
usb_storage 35142 0
floppy 48087 0
ohci_hcd 22059 0
pata_ali 12880 0
sata_uli 12449 2
libata 125014 3 sata_uli,pata_ali,ata_generic
ehci_hcd 35509 0
scsi_mod 135037 5 libata,usb_storage,sr_mod,sd_mod,sg
usbcore 104555 5 ehci_hcd,ohci_hcd,usb_storage,usbhid
skge 35968 0
usb_common 12338 1 usbcore
root@debian:/home/debian# lspci -nnvv
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge [1002:5a33] (rev 01)
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge [1002:5a3f] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ff400000-ff4fffff
Prefetchable memory behind bridge: bff00000-dfefffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [b0] Subsystem: Elitegroup Computer Systems Device [1019:1b36]
00:19.0 PCI bridge [0604]: ULi Electronics Inc. M5249 HTT to PCI Bridge [10b9:5249] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR+ <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff500000-ff5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR+ <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [c0] HyperTransport: MSI Mapping Enable+ Fixed+
00:1c.0 USB controller [0c03]: ULi Electronics Inc. USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at ff6ff000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:1c.1 USB controller [0c03]: ULi Electronics Inc. USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at ff6fe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:1c.2 USB controller [0c03]: ULi Electronics Inc. USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (20000ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 19
Region 0: Memory at ff6fd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:1c.3 USB controller [0c03]: ULi Electronics Inc. USB 2.0 Controller [10b9:5239] (rev 01) (prog-if 20 [EHCI])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 23
Region 0: Memory at ff6fcc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=0090
Kernel driver in use: ehci_hcd
00:1d.0 Audio device [0403]: ULi Electronics Inc. HD Audio Controller [10b9:5461]
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 20000ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ff6f8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_hda_intel
00:1e.0 ISA bridge [0601]: ULi Electronics Inc. PCI to LPC Controller [10b9:1573] (rev 31)
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 6000ns max)
00:1e.1 Bridge [0680]: ULi Electronics Inc. M7101 Power Management Controller [PMU] [10b9:7101]
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:1f.0 IDE interface [0101]: ULi Electronics Inc. M5229 IDE [10b9:5229] (rev c7) (prog-if 8a [Master SecP PriP])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 21
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at ff00 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_ali
00:1f.1 RAID bus controller [0104]: ULi Electronics Inc. ULi 5287 SATA [10b9:5287] (rev 02)
Subsystem: Elitegroup Computer Systems Device [1019:5287]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 512 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at ec00 [size=16]
Region 1: I/O ports at e800 [size=8]
Region 2: I/O ports at e400 [size=16]
Region 3: I/O ports at e000 [size=8]
Region 4: I/O ports at dc00 [size=32]
Region 5: Memory at ff6fc800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_uli
01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] [1002:5a61] (prog-if 00 [VGA controller])
Subsystem: Elitegroup Computer Systems Device [1019:1b36]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at b800 [size=256]
Region 2: Memory at ff4f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at ff4c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Kernel driver in use: radeon
02:15.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller [11ab:4320] (rev 13)
Subsystem: Elitegroup Computer Systems Marvell 88E8001 Gigabit Ethernet Controller (ECS) [1019:8001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at ff5fc000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at c800 [size=256]
Expansion ROM at ff5c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=7 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
Read-only fields:
[PN] Part number: Yukon 88E8001
[EC] Engineering changes: Rev. 1.3
[MN] Manufacture ID: 4d 61 72 76 65 6c 6c
[SN] Serial number: AbCdEfG334454
[CP] Extended capability: 01 10 cc 03
[RV] Reserved: checksum good, 10 byte(s) reserved
Read/write fields:
[RW] Read-write area: 121 byte(s) free
End
Kernel driver in use: skge
Offline
Pages: 1
[ Generated in 0.016 seconds, 7 queries executed - Memory usage: 1.61 MiB (Peak: 1.77 MiB) ]