SliTaz Forum
You are not logged in.
Pages: 1
hi everybody,my acer aspire laptop has bcm57786 ethernet card but when i opened live slitaz 5.0
Offline
my wired lan does not show eth0,it is showing dummy0,lo,tunl0 when i configured dummy0 but it is not work
Offline
i configured on rcS.conf load modules first broadcom and tg3 but no success.
when i bashed: ifconfig etho and the result -> ifconfig: eth0: error fetching interface information: Device not found
Offline
Open terminal
type
[c]lspci -nn[/c]
hit enter
Post the output
Online
execuse me but my laptop is not near me but my ethernet card is BCM57786 NetXtreme Gigabit ethernet
i bashed lspci command before.
Offline
The tg3 kernel module and tigon firmware are on the slitaz-5.0 live cd.
Check dmesg for errors.
Online
yes tg3 kernel module in slitaz 5.0 but it didn't recognize i will upload my demsg log and lspci output
Offline
here is my lspci -nn output:
00:00.0 Host bridge [0600]: Intel Corporation Haswell-ULT DRAM Controller [8086:0a04] (rev 09)
00:02.0 VGA compatible controller [0300]: Intel Corporation Haswell-ULT Integrated Graphics Controller [8086:0a16] (rev 09)
00:03.0 Audio device [0403]: Intel Corporation Haswell-ULT HD Audio Controller [8086:0a0c] (rev 09)
00:14.0 USB controller [0c03]: Intel Corporation Lynx Point-LP USB xHCI HC [8086:9c31] (rev 04)
00:16.0 Communication controller [0780]: Intel Corporation Lynx Point-LP HECI #0 [8086:9c3a] (rev 04)
00:1b.0 Audio device [0403]: Intel Corporation Lynx Point-LP HD Audio Controller [8086:9c20] (rev 04)
00:1c.0 PCI bridge [0604]: Intel Corporation Lynx Point-LP PCI Express Root Port 3 [8086:9c14] (rev e4)
00:1c.3 PCI bridge [0604]: Intel Corporation Lynx Point-LP PCI Express Root Port 4 [8086:9c16] (rev e4)
00:1c.4 PCI bridge [0604]: Intel Corporation Lynx Point-LP PCI Express Root Port 5 [8086:9c18] (rev e4)
00:1d.0 USB controller [0c03]: Intel Corporation Lynx Point-LP USB EHCI #1 [8086:9c26] (rev 04)
00:1f.0 ISA bridge [0601]: Intel Corporation Lynx Point-LP LPC Controller [8086:9c43] (rev 04)
00:1f.2 SATA controller [0106]: Intel Corporation Lynx Point-LP SATA Controller 1 [AHCI mode] [8086:9c03] (rev 04)
00:1f.3 SMBus [0c05]: Intel Corporation Lynx Point-LP SMBus Controller [8086:9c22] (rev 04)
01:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM57786 Gigabit Ethernet PCIe [14e4:16b3] (rev 01)
01:00.1 SD Host controller [0805]: Broadcom Corporation BCM57765/57785 SDXC/MMC Card Reader [14e4:16bc] (rev 01)
02:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01)
03:00.0 Display controller [0380]: Advanced Micro Devices, Inc. [AMD/ATI] Mars [Radeon HD 8670A/8670M/8750M] [1002:6600]
here is my dmesg output:
0-0xfd63] has been reserved
system 00:04: [io 0xffff] has been reserved
system 00:04: [io 0xffff] has been reserved
system 00:04: [io 0xffff] has been reserved
system 00:04: [io 0x1800-0x18fe] has been reserved
system 00:04: [io 0x164e-0x164f] has been reserved
system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:05: [io 0x0070-0x0077]
pnp 00:05: [irq 8]
pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:06: [io 0x1854-0x1857]
system 00:06: [io 0x1854-0x1857] has been reserved
system 00:06: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
pnp 00:07: [io 0x0060]
pnp 00:07: [io 0x0064]
pnp 00:07: [irq 1]
pnp 00:07: Plug and Play ACPI device, IDs MSF0001 PNP0303 (active)
pnp 00:08: [irq 12]
pnp 00:08: Plug and Play ACPI device, IDs SYN1b6d PNP0f13 (active)
pnp 00:09: [mem 0xfed1c000-0xfed1ffff]
pnp 00:09: [mem 0xfed10000-0xfed17fff]
pnp 00:09: [mem 0xfed18000-0xfed18fff]
pnp 00:09: [mem 0xfed19000-0xfed19fff]
pnp 00:09: [mem 0xe0000000-0xefffffff]
pnp 00:09: [mem 0xfed20000-0xfed3ffff]
pnp 00:09: [mem 0xfed90000-0xfed93fff]
pnp 00:09: [mem 0xff000000-0xff000fff]
pnp 00:09: [mem 0xff010000-0xffffffff]
pnp 00:09: [mem 0xfee00000-0xfeefffff]
pnp 00:09: [mem 0x9fa20000-0x9fa20fff]
pnp 00:09: [mem 0xffffffff-0x0000fffe]
system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:09: [mem 0xfed10000-0xfed17fff] has been reserved
system 00:09: [mem 0xfed18000-0xfed18fff] has been reserved
system 00:09: [mem 0xfed19000-0xfed19fff] has been reserved
system 00:09: [mem 0xe0000000-0xefffffff] has been reserved
system 00:09: [mem 0xfed20000-0xfed3ffff] has been reserved
system 00:09: [mem 0xfed90000-0xfed93fff] has been reserved
system 00:09: [mem 0xff000000-0xff000fff] has been reserved
system 00:09: [mem 0xff010000-0xffffffff] could not be reserved
system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved
system 00:09: [mem 0x9fa20000-0x9fa20fff] has been reserved
system 00:09: [mem 0xffffffff-0x0000fffe] could not be reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
Switching to clocksource acpi_pm
pci 0000:01:00.0: no compatible bridge window for [mem 0xfffff800-0xffffffff pref]
pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
pci 0000:03:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:1c.0: BAR 8: assigned [mem 0x9fb00000-0x9fbfffff]
pci 0000:00:1c.3: BAR 9: assigned [mem 0x9fc00000-0x9fcfffff pref]
pci 0000:01:00.0: BAR 6: assigned [mem 0xc0430000-0xc04307ff pref]
pci 0000:00:1c.0: PCI bridge to [bus 01-01]
pci 0000:00:1c.0: bridge window [mem 0x9fb00000-0x9fbfffff]
pci 0000:00:1c.0: bridge window [mem 0xc0400000-0xc04fffff 64bit pref]
pci 0000:02:00.0: BAR 6: assigned [mem 0x9fc00000-0x9fc0ffff pref]
pci 0000:00:1c.3: PCI bridge to [bus 02-02]
pci 0000:00:1c.3: bridge window [mem 0xc0600000-0xc06fffff]
pci 0000:00:1c.3: bridge window [mem 0x9fc00000-0x9fcfffff pref]
pci 0000:03:00.0: BAR 6: assigned [mem 0xc0540000-0xc055ffff pref]
pci 0000:00:1c.4: PCI bridge to [bus 03-03]
pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
pci 0000:00:1c.4: bridge window [mem 0xc0500000-0xc05fffff]
pci 0000:00:1c.4: bridge window [mem 0xa0000000-0xafffffff 64bit pref]
pci 0000:00:1c.0: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.4: setting latency timer to 64
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x9fa00000-0xfeafffff]
pci_bus 0000:01: resource 1 [mem 0x9fb00000-0x9fbfffff]
pci_bus 0000:01: resource 2 [mem 0xc0400000-0xc04fffff 64bit pref]
pci_bus 0000:02: resource 1 [mem 0xc0600000-0xc06fffff]
pci_bus 0000:02: resource 2 [mem 0x9fc00000-0x9fcfffff pref]
pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
pci_bus 0000:03: resource 1 [mem 0xc0500000-0xc05fffff]
pci_bus 0000:03: resource 2 [mem 0xa0000000-0xafffffff 64bit pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:02.0: Boot video device
pci 0000:00:14.0: power state changed by ACPI to D0
pci 0000:00:14.0: power state changed by ACPI to D0
pci 0000:00:14.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:14.0: PCI INT A disabled
pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
pci 0000:00:1d.0: PCI INT A disabled
PCI: CLS 64 bytes, default 64
Simple Boot Flag at 0x44 set to 0x1
apm: BIOS not found.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
fuse init (API version 7.17)
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
Btrfs loaded
msgmni has been set to 1721
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
ACPI: AC Adapter [ACAD] (off-line)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
ACPI: acpi_idle registered with cpuidle
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
ACPI: Battery Slot [BAT1] (battery present)
Non-volatile memory driver v1.3
brd: module loaded
loop: module loaded
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x3 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo only pio slum part apst
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m2048@0xc071b000 port 0xc071b100 irq 19
ata2: SATA max UDMA/133 abar m2048@0xc071b000 port 0xc071b180 irq 19
ata3: DUMMY
ata4: DUMMY
scsi4 : pata_legacy
ata5: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: ST500LT012-9WS142, 0001SDM1, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST500LT012-9WS14 0001 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: Attached scsi generic sg0 type 0
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
Refined TSC clocksource calibration: 2294.688 MHz.
Switching to clocksource tsc
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: MATSHITADVD-RAM UJ8D2Q, 1.10, max UDMA/133
ata2.00: configured for UDMA/133
scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ8D2Q 1.10 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
scsi5 : pata_legacy
ata6: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
v1.01-e (2.4 port) Sep-11-2006 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/drivers.html
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
tlan: ThunderLAN driver v1.17
tlan: 0 devices installed, PCI: 0 EISA: 0
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.0: irq 23, io mem 0xc071c000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
input: PC Speaker as /devices/platform/pcspkr/input/input0
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 242 bytes nvram
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
IPv4 over IPv4 tunneling driver
GRE over IPv4 demultiplexor driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 33
RxRPC: Registered security type 2 'rxkad'
Registering the dns_resolver key type
Using IPI No-Shortcut mode
registered taskstats version 1
rtc_cmos 00:05: setting system clock to 2015-05-12 11:01:15 UTC (1431428475)
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
usb 1-1: new high-speed USB device number 2 using ehci_hcd
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 8 ports detected
psmouse serio1: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1e0b1, caps: 0xf00173/0x240000/0xa2400
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input2
EXT3-fs (sda2): error: couldn't mount because of unsupported optional features (240)
EXT4-fs (sda2): couldn't mount as ext2 due to feature incompatibilities
EXT4-fs (sda2): INFO: recovery required on readonly filesystem
EXT4-fs (sda2): write access will be enabled during recovery
EXT4-fs (sda2): orphan cleanup on readonly fs
EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 1179658
EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 1179657
EXT4-fs (sda2): ext4_orphan_cleanup: deleting unreferenced inode 1179656
EXT4-fs (sda2): 3 orphan inodes deleted
EXT4-fs (sda2): recovery complete
EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
Freeing unused kernel memory: 444k freed
udevd[965]: starting version 182
EXT4-fs (sda2): re-mounted. Opts: user_xattr,barrier=1,data=ordered
EXT4-fs (sda2): re-mounted. Opts: user_xattr,barrier=1,data=ordered
cfg80211: Calling CRDA to update world regulatory domain
snd_hda_intel 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
snd_hda_intel 0000:00:03.0: setting latency timer to 64
hda-intel: azx_get_response timeout, switching to polling mode: last cmd=0x000f0000
hda-intel: Codec #0 probe error; disabling it...
hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x000f0001
snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
snd_hda_intel 0000:00:1b.0: setting latency timer to 64
Linux agpgart interface v0.103
[drm] Initialized drm 1.1.0 20060810
[drm] radeon defaulting to kernel modesetting.
[drm] radeon kernel modesetting enabled.
xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
xhci_hcd 0000:00:14.0: power state changed by ACPI to D0
xhci_hcd 0000:00:14.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
xhci_hcd 0000:00:14.0: setting latency timer to 64
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 9 ports detected
xhci_hcd 0000:00:14.0: xHCI Host Controller
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
wmi: Mapper loaded
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID0]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input4
ACPI: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0E:00/input/input5
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
ACPI: Power Button [PWRF]
usb 2-3: new full-speed USB device number 2 using xhci_hcd
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.0/input/input7
generic-usb 0003:046D:C52F.0001: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-3/input0
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb2/2-3/2-3:1.1/input/input8
generic-usb 0003:046D:C52F.0002: input,hiddev0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-3/input1
usb 2-5: new full-speed USB device number 3 using xhci_hcd
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
usb 2-8: new high-speed USB device number 4 using xhci_hcd
NET: Registered protocol family 10
[Firmware Bug]: battery: (dis)charge rate invalid.
usb 2-1: new high-speed USB device number 5 using xhci_hcd
scsi6 : usb-storage 2-1:1.0
scsi 6:0:0:0: Direct-Access SanDisk Cruzer Blade 1.26 PQ: 0 ANSI: 6
sd 6:0:0:0: Attached scsi generic sg2 type 0
sd 6:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 6:0:0:0: [sdb] Attached SCSI disk
Offline
here is my lsmod output :
Module Size Used by Not tainted
ipv6 178394 36
btusb 8477 0
bluetooth 59080 1 btusb
video 9491 0
button 3282 0
wmi 5839 0
xhci_hcd 57203 0
cifs 182187 0
radeon 561008 0
i2c_algo_bit 3627 1 radeon
ttm 36568 1 radeon
drm_kms_helper 17504 1 radeon
drm 118530 3 radeon,ttm,drm_kms_helper
agpgart 17563 2 ttm,drm
hwmon 865 1 radeon
i2c_core 12290 4 radeon,i2c_algo_bit,drm_kms_helper,drm
r8169 33688 0
snd_hda_codec_realtek 134555 1
snd_hda_intel 16713 0
snd_hda_codec 45584 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 3811 1 snd_hda_codec
snd_pcm 42922 2 snd_hda_intel,snd_hda_codec
snd_page_alloc 4669 2 snd_hda_intel,snd_pcm
snd_timer 12069 1 snd_pcm
snd 33323 6 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
soundcore 3254 1 snd
tg3 103663 0
broadcom 4694 0
libphy 11158 2 tg3,broadcom
ath9k 61769 0
ath9k_common 1352 1 ath9k
ath9k_hw 303000 2 ath9k,ath9k_common
ath 10422 3 ath9k,ath9k_common,ath9k_hw
mac80211 161311 1 ath9k
cfg80211 117318 3 ath9k,ath,mac80211
rfkill 10151 2 bluetooth,cfg80211
Offline
but i dont understand why eth0 is not loading.and slitaz did not recognize the ethernet card
Offline
Googled around BCM57765 and found: http://forums.linuxmint.com/viewtopic.php?f=150&t=155202
Problem will be solved in the new Linux Kernel (3.13 in that forum topic). Alas, SliTaz provided only Linux Kernel 3.2.53 at the moment and here is no plan to move to the newer Kernels, sorry.
Offline
is it so hard compile new kernel higher than 3.2
Offline
is there any patch,script or compiling 3.2 with broadcom support
Offline
http://forum.slitaz.org/topic/kernel-higher-than-32
Offline
Dear mahmutov!
Can you to write your thoughts in the single forum post?
Do you think here is a chat?
Why you press "Send" button three times a minute???
Back to the topic, I don't know about such a patches or scripts.
Offline
execuse me is it problem "Send" button three times a minute?,
is it so hard compile new kernel higher than 3.2
Offline
and i joined freenode-slitaz channel anybody is no around for my questions.
Offline
Sorry and good bye.
Offline
hi everybody i solved my ethernet problem.
1-download linux libre kernel 3.16.7
2- http://doc.slitaz.org/en:guides:kernel i compiled
3-and reboot with new kernel
eth0 came it is working best
slitaz with kernel 3.16.7 
Offline
Pages: 1
[ Generated in 0.034 seconds, 7 queries executed - Memory usage: 1.6 MiB (Peak: 1.77 MiB) ]