SliTaz Forum
You are not logged in.
Pages: 1
Bonjour,
je viens d'installer SliTaz 4.0 sur le disque dur de mon PC (il n'y a aucun autre système). Je n'arrive pas à mettre la wifi, ni à me connecter par câble.
Après avoir cherché des infos : j'ai installé le module ipw2200 qui manquait, téléchargé depuis
wget http://people.slitaz.org/~mojo/stuff/ipw2200-firmware-3.1.tazpkg.
j'ai suivi la procédure de dépannage (http://doc.slitaz.org/fr:guides:wifi-easy#demarrer-le-wifi), voici les résultats mais je n'y comprends rien à vrai dire.
Pouvez-vous m'aider ? Un grand merci ! (Je suis vraiment débutante et je peux comprendre vite mais il faut m'expliquer longtemps et surtout, précisément sans vouloir abuser de votre temps)
root@slitaz:/home/tux# lspci grep -i network
Usage: lspci [<switches>]
Basic display modes:
-mm Produce machine-readable output (single -m for an obsolete format)
-t Show bus tree
Display options:
-v Be verbose (-vv for very verbose)
-k Show kernel drivers handling each device
-x Show hex-dump of the standard part of the config space
-xxx Show hex-dump of the whole config space (dangerous; root only)
-xxxx Show hex-dump of the 4096-byte extended config space (root only)
-b Bus-centric view (addresses and IRQ's as seen by the bus)
-D Always show domain numbers
Resolving of device ID's to names:
-n Show numeric ID's
-nn Show both textual and numeric ID's (names & numbers)
-q Query the PCI ID database for unknown ID's via DNS
-qq As above, but re-query locally cached entries
-Q Query the PCI ID database for all ID's via DNS
Selection of devices:
-s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]] Show only devices in selected slots
-d [<vendor>]:[<device>] Show only devices with specified ID's
Other options:
-i <file> Use specified ID database instead of network
-p <file> Look up kernel modules in a given file instead of default modules.pcimap
-M Enable `bus mapping' mode (dangerous; root only)
PCI access options:
-A <method> Use the specified PCI access method (see `-A help' for a list)
-O <par>=<val> Set PCI access parameter (see `-O help' for a list)
-G Enable PCI access debugging
-H <mode> Use direct hardware access (<mode> = 1 or 2)
-F <file> Read PCI configuration dump from a given file
root@slitaz:/home/tux# modprobe your_module
modprobe: module your_module not found in modules.dep
root@slitaz:/home/tux# dmesg tail
nyansky <maxk@qualcomm.com>
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-840.c:v1.01-e (2.4 port) Sep-11-2006 Donald Becker <becker@scyld.com>
http://www.scyld.com/network/drivers.html
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 10, io mem 0xd0000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 6 (level, low) -> IRQ 6
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 6, io base 0x00001800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 6 (level, low) -> IRQ 6
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 6, io base 0x00001820
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 6 (level, low) -> IRQ 6
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 6, io base 0x00001840
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /devices/platform/pcspkr/input/input0
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
hub 2-0:1.0: over-current change on port 1
hub 2-0:1.0: over-current change on port 2
hub 1-0:1.0: over-current change on port 1
hub 1-0:1.0: over-current change on port 2
usb 4-2: new low speed USB device using uhci_hcd and address 2
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x126eb1, caps: 0xa04713/0x4000/0x0
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input2
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input3
generic-usb 0003:046D:C05B.0001: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-2/input0
EXT4-fs (hda1): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext2 filesystem) readonly on device 3:1.
Freeing unused kernel memory: 408k freed
EXT4-fs (hda1): re-mounted. Opts: barrier=1,data=writeback
EXT4-fs (hda1): re-mounted. Opts: barrier=1,data=writeback
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 855GM Chipset
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
Intel ICH 0000:00:1f.5: setting latency timer to 64
intel8x0_measure_ac97_clock: measured 50259 usecs (2423 samples)
intel8x0: clocking to 48000
Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
MC'97 0 converters and GPIO not ready (0x1)
[drm] Initialized drm 1.1.0 20060810
[drm] radeon defaulting to kernel modesetting.
[drm] radeon kernel modesetting enabled.
radeon 0000:01:00.0: power state changed by ACPI to D0
radeon 0000:01:00.0: power state changed by ACPI to D0
radeon 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 6 (level, low) -> IRQ 6
[drm] initializing kernel modesetting (RV350 0x1002:0x4E50).
[drm] register mmio base: 0xD0100000
[drm] register mmio size: 65536
agpgart-intel 0000:00:00.0: AGP 2.0 bridge
agpgart-intel 0000:00:00.0: putting AGP V2 device into 1x mode
radeon 0000:01:00.0: putting AGP V2 device into 1x mode
radeon 0000:01:00.0: GTT: 256M 0xE0000000 - 0xEFFFFFFF
[drm] Generation 2 PCI interface, using max accessible memory
radeon 0000:01:00.0: VRAM: 128M 0x00000000D8000000 - 0x00000000DFFFFFFF (64M used)
[drm] radeon: irq initialized.
[drm] Detected VRAM RAM=128M, BAR=128M
[drm] RAM width 128bits DDR
[TTM] Zone kernel: Available graphics memory: 256358 kiB.
[TTM] Initializing pool allocator.
[drm] radeon: 64M of VRAM memory ready
[drm] radeon: 256M of GTT memory ready.
[drm] radeon: 1 quad pipes, 1 Z pipes initialized.
radeon 0000:01:00.0: WB disabled
[drm] Loading R300 Microcode
[drm] radeon: ring at 0x00000000E0001000
[drm] ring test succeeded in 1 usecs
[drm] radeon: ib pool ready.
[drm] ib test succeeded in 0 usecs
[drm] Panel ID String: QDS
[drm] Panel Size 1280x800
[drm] Radeon Display Connectors
[drm] Connector 0:
[drm] VGA
[drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[drm] Encoders:
[drm] CRT1: INTERNAL_DAC1
[drm] Connector 1:
[drm] LVDS
[drm] Encoders:
[drm] LCD1: INTERNAL_LVDS
[drm] Connector 2:
[drm] S-video
[drm] Encoders:
[drm] TV1: INTERNAL_DAC2
[drm] radeon: power management initialized
[drm] fb mappable at 0xD8040000
[drm] vram apper at 0xD8000000
[drm] size 4096000
[drm] fb depth is 24
[drm] pitch is 5120
Console: switching to colour frame buffer device 160x50
fb0: radeondrmfb frame buffer device
drm: registered panic notifier
[drm] Initialized radeon 2.7.0 20080528 for 0000:01:00.0 on minor 0
b44 0000:02:02.0: PCI INT A -> Link[LNKD] -> GSI 6 (level, low) -> IRQ 6
ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x04, vendor 0x4243)
ssb: Core 1 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x02, vendor 0x4243)
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
b44: b44.c:v2.0
b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:5b:ac:6f
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
cfg80211: Calling CRDA to update world regulatory domain
libipw: 802.11 data/management/control stack, git-1.1.13
libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ipw2200 0000:02:04.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
ipw2200: Unable to load firmware: -2
ipw2200: failed to register network device
ipw2200 0000:02:04.0: PCI INT A disabled
ipw2200: probe of 0000:02:04.0 failed with error -5
yenta_cardbus 0000:02:06.0: CardBus bridge found [1025:0064]
yenta_cardbus 0000:02:06.0: Enabling burst memory read transactions
yenta_cardbus 0000:02:06.0: Using CSCINT to route CSC interrupts to PCI
yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:06.0: TI: mfunc 0x01a21b22, devctl 0x64
yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x08b8, PCI irq 10
yenta_cardbus 0000:02:06.0: Socket status: 30000006
pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06
yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [io 0x4000-0x4fff]
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x4000-0x4fff: excluding 0x4000-0x40ff 0x4400-0x44ff
yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0xd0200000-0xd05fffff]
pcmcia_socket pcmcia_socket0: cs: memory probe 0xd0200000-0xd05fffff: excluding 0xd0200000-0xd023ffff
yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0x20000000-0x25ffffff pref]
pcmcia_socket pcmcia_socket0: cs: memory probe 0x20000000-0x25ffffff: excluding 0x20000000-0x25ffffff
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1c0-0x1cf 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x377
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xd3fff 0xdc000-0xfffff
pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: clean.
pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
ACPI: Power Button [PWRF]
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:02/LNXVIDEO:00/input/input7
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
b44 ssb0:0: eth0: Flow control is off for TX and off for RX
mtrr: no MTRR for d8000000,4000000 found
usb 1-4: new high speed USB device using ehci_hcd and address 3
scsi0 : usb-storage 1-4:1.0
scsi 0:0:0:0: Direct-Access Sony Storage Media 1.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
usb 1-4: USB disconnect, address 3
usb 4-2: USB disconnect, address 2
usb 1-3: new high speed USB device using ehci_hcd and address 4
scsi1 : usb-storage 1-3:1.0
scsi 1:0:0:0: Direct-Access Sony Storage Media 1.00 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Attached SCSI removable disk
usb 4-2: new low speed USB device using uhci_hcd and address 3
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input8
generic-usb 0003:046D:C05B.0002: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-2/input0
b44 ssb0:0: eth0: powering down PHY
b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
b44 ssb0:0: eth0: Flow control is off for TX and off for RX
b44 ssb0:0: eth0: powering down PHY
b44 ssb0:0: eth0: powering down PHY
b44 ssb0:0: eth0: powering down PHY
b44 ssb0:0: eth0: powering down PHY
b44 ssb0:0: eth0: powering down PHY
b44 ssb0:0: eth0: powering down PHY
usb 4-2: USB disconnect, address 3
usb 4-2: new low speed USB device using uhci_hcd and address 4
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input9
generic-usb 0003:046D:C05B.0003: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-2/input0
usb 1-3: USB disconnect, address 4
usb 4-2: USB disconnect, address 4
usb 1-3: new high speed USB device using ehci_hcd and address 7
scsi2 : usb-storage 1-3:1.0
scsi 2:0:0:0: Direct-Access Sony Storage Media 1.00 PQ: 0 ANSI: 2
sd 2:0:0:0: [sdb] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1 sdb2
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI removable disk
usb 4-2: new low speed USB device using uhci_hcd and address 5
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input10
generic-usb 0003:046D:C05B.0004: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-2/input0
usb 1-3: USB disconnect, address 7
usb 4-2: USB disconnect, address 5
usb 1-3: new high speed USB device using ehci_hcd and address 9
scsi3 : usb-storage 1-3:1.0
scsi 3:0:0:0: Direct-Access Sony Storage Media 1.00 PQ: 0 ANSI: 2
sd 3:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
sd 3:0:0:0: [sdc] Write Protect is off
sd 3:0:0:0: [sdc] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdc] Assuming drive cache: write through
sd 3:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1 sdc2
sd 3:0:0:0: [sdc] Assuming drive cache: write through
sd 3:0:0:0: [sdc] Attached SCSI removable disk
usb 4-2: new low speed USB device using uhci_hcd and address 6
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input11
generic-usb 0003:046D:C05B.0005: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-2/input0
usb 1-3: USB disconnect, address 9
usb 4-2: USB disconnect, address 6
usb 4-2: new low speed USB device using uhci_hcd and address 7
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input12
generic-usb 0003:046D:C05B.0006: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-2/input0
b44 ssb0:0: eth0: powering down PHY
usb 4-2: USB disconnect, address 7
usb 1-3: new high speed USB device using ehci_hcd and address 12
scsi4 : usb-storage 1-3:1.0
scsi 4:0:0:0: Direct-Access Sony Storage Media 1.00 PQ: 0 ANSI: 2
sd 4:0:0:0: [sdd] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 23 00 00 00
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sd 4:0:0:0: Attached scsi generic sg0 type 0
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sdd: sdd1 sdd2
sd 4:0:0:0: [sdd] Assuming drive cache: write through
sd 4:0:0:0: [sdd] Attached SCSI removable disk
usb 4-2: new low speed USB device using uhci_hcd and address 8
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input13
generic-usb 0003:046D:C05B.0007: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-2/input0
root@slitaz:/home/tux# lsmod
Module Size Used by Not tainted
video 9783 0
output 1144 1 video
button 3602 0
pcmcia 24993 0
yenta_socket 16223 0
pcmcia_rsrc 6989 1 yenta_socket
pcmcia_core 8413 3 pcmcia,yenta_socket,pcmcia_rsrc
ipw2200 108387 0
libipw 17987 1 ipw2200
cfg80211 99896 2 ipw2200,libipw
rfkill 10682 1 cfg80211
lib80211 2676 2 ipw2200,libipw
b44 20102 0
ssb 24436 1 b44
radeon 673881 1
ttm 35361 1 radeon
drm_kms_helper 18798 1 radeon
drm 111992 3 radeon,ttm,drm_kms_helper
hwmon 993 1 radeon
i2c_algo_bit 3479 1 radeon
i2c_core 12192 4 radeon,drm_kms_helper,drm,i2c_algo_bit
snd_intel8x0m 8083 0
snd_intel8x0 19786 1
snd_ac97_codec 77963 2 snd_intel8x0m,snd_intel8x0
ac97_bus 718 1 snd_ac97_codec
snd_pcm 43737 3 snd_intel8x0m,snd_intel8x0,snd_ac97_codec
snd_timer 12515 1 snd_pcm
snd 33394 7 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 3357 1 snd
snd_page_alloc 4853 3 snd_intel8x0m,snd_intel8x0,snd_pcm
intel_agp 7908 1
intel_gtt 9214 1 intel_agp
agpgart 18221 4 ttm,drm,intel_agp,intel_gtt
/etc/network.conf: SliTaz system wide networking configuration.
# Config file used by: /etc/init.d/network.sh
#
# Set default interface.
INTERFACE="eth0"
# Dynamic IP address.
# Enable/disable DHCP client at boot time.
DHCP="yes"
# Static IP address.
# Enable/disable static IP at boot time.
STATIC="no"
# Set IP address and netmask for a static IP.
IP="192.168.0.6"
NETMASK="255.255.255.0"
[ Lecture de 38 lignes ]
^G Aide ^O Écrire ^R Lire fich.^Y Page préc.^K Couper ^C Pos. cur.
^X Quitter ^J Justifier ^W Chercher ^V Page suiv.^U Coller ^T Orthograp.
root@slitaz:/home/tux# ifconfig eth1 up
ifconfig: SIOCGIFFLAGS: No such device
root@slitaz:/home/tux# ifconfig -a
dummy0 Link encap:Ethernet HWaddr 4E:3F:B7:6F:AE:B2
BROADCAST NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 00:C0:9F:5B:AC:6F
inet addr:192.168.0.6 Bcast:192.168.0.255 Mask:255.255.255.0
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:46 errors:0 dropped:4 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5254 (5.1 KiB) TX bytes:1304 (1.2 KiB)
Interrupt:6
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3076 errors:0 dropped:0 overruns:0 frame:0
TX packets:3076 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:611634 (597.2 KiB) TX bytes:611634 (597.2 KiB)
root@slitaz:/home/tux# iwconfig
lo no wireless extensions.
dummy0 no wireless extensions.
eth0 no wireless extensions.
root@slitaz:/home/tux# /etc/init.d/network.sh restart
Stopping all interfaces
ifconfig: SIOCGIFFLAGS: No such device
Killing all daemons
killall: udhcpc: no process killed
wlan0 No such device
wlan0 is not a wifi interface, changing it.
Configuring ...lo no wireless extensions.
dummy0 no wireless extensions.
eth0 no wireless extensions.
[ OK ]
iwconfig: unknown command "any"
Starting udhcpc client on: ...
udhcpc: SIOCGIFINDEX: No such device
root@slitaz:/home/tux# ifconfig -a
dummy0 Link encap:Ethernet HWaddr 4E:3F:B7:6F:AE:B2
BROADCAST NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth0 Link encap:Ethernet HWaddr 00:C0:9F:5B:AC:6F
inet addr:192.168.0.6 Bcast:192.168.0.255 Mask:255.255.255.0
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:46 errors:0 dropped:4 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5254 (5.1 KiB) TX bytes:1304 (1.2 KiB)
Interrupt:6
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3076 errors:0 dropped:0 overruns:0 frame:0
TX packets:3076 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:611634 (597.2 KiB) TX bytes:611634 (597.2 KiB)
Offline
Hello
the command mentioned on the help page is: lspci | grep -i network
the issue:
ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
ipw2200: Unable to load firmware: -2
--> root@slitaz:/home/tux# modprobe your_module <-- read:
modprobe -r ipw2200
modprobe ipw2200
same thing:
http://vanilla.slitaz.org/index.php?p=/discussion/comment/11534#Comment_11534
Surely a native french speaker will come along....I drop out..
Offline
Bonjour sd,
Avec SliTaz, tu dois choisir : ethernet ou wifi ; mais tu ne pourras pas travailler indifféremment avec l'un ou l'autre sans faire quelques modifications à chaque fois que tu changeras de type de connexion.
On va commencer par un état des lieux. Tu as installé la 4.0,
As-tu essayé tout d'abord de te connecter avec le câble ethernet ? si oui, pas de connexion ?
Ensuite, quand tu as essayé d'activer ton wifi, as-tu modifié quelque chose dans network.conf ?
Côté matériel, même si je pense avoir trouvé la réponse dans ton post précédent. Ouvre un terminal, tape
lspci -nn
et poste la réponse.
2 précisions :
Attention à la syntaxe des commandes : tous les caractères sont utiles et le système fait la distinction entre majuscules et minuscules...
Ne t'inquiète pas si je suis plusieurs jours sans donner de nouvelle, j'ai peu de temps libre des temps-ci
Offline
Bonjour Ceel.
J'ai fait une première installation sur disque dur où j'ai tout essayé pour me connecter par câble ou wifi, l'un après l'autre. La machine ne détectait aucun réseau. J'ai fait pas mal de modifications dans le network.conf mais ça n'a pas marché non plus, installé le module ipw2200 mais ensuite pas moyen pour l'ordi de trouver les modules complémentaires.
Du coup, je suis repartie à zéro en réinstallant Slitaz 4.0. J'ai donc revérifié que tout marchait mais non et réinstallé le module pour ipw2200. C'est tout. La première fois, j'ai fait des modif à la main et essayé de configurer le réseau mais pas de changements ni de réactions.
Au démarrage, il indique 5 fois ERROR: unable to find IOAPIC for GNU +un numéro.
J'ai aussi remarqué que c'est la version cooking, je croyais que c'était une version stable ... Bon ça n'a sûrement aucun rapport de toute façon.
Voici la réponse :
root@slitaz:/home/tux# lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3580] (rev 02)
00:00.1 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3584] (rev 02)
00:00.3 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3585] (rev 02)
00:01.0 PCI bridge [0604]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to AGP Controller [8086:3581] (rev 02)
00:1d.0 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 03)
00:1d.1 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 03)
00:1d.2 USB controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 03)
00:1d.7 USB controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 83)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge [8086:24cc] (rev 03)
00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE Controller [8086:24ca] (rev 03)
00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller [8086:24c3] (rev 03)
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 03)
00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller [8086:24c6] (rev 03)
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50]
02:02.0 Ethernet controller [0200]: Broadcom Corporation BCM4401 100Base-T [14e4:4401] (rev 01)
02:04.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection [8086:4220] (rev 05)
02:06.0 CardBus bridge [0607]: Texas Instruments PCIxx21/x515 Cardbus Controller [104c:8031]
02:06.2 FireWire (IEEE 1394) [0c00]: Texas Instruments OHCI Compliant IEEE 1394 Host Controller [104c:8032]
02:06.3 Mass storage controller [0180]: Texas Instruments PCIxx21 Integrated FlashMedia Controller [104c:8033]
root@slitaz:/home/tux#
Je vais jeter un œil sur le lien de sixofeigth pour voir si je peux avancer un peu en attendant de tes nouvelles ...
Bonne journée.
Offline
Bonsoir sd,
On va d'abord essayer de faire fonctionner la connexion par câble ethernet. Normalement, après l'installation, ça devrait marcher ; on voit dans ton premier post (la commande [c]lsmod[/c]) que le noyau a chargé les drivers de ta carte [c]b44[/c] et [c]ssb[/c].
Tu peux t'en assurer en retapant [c]lsmod[/c] dans un terminal.
Offline
Bonsoir,
Merci pour cette réactivité. Je passe par le tazpanel pour configurer la connexion mais rien ne se passe à vrai dire ; que dois-je faire concrètement ?
C'est vrai qu'avant je n'avais pas le eth1 mais que dois-je choisir ?
Offline
Par défaut, pour la connexion ethernet, tu n'as rien à configurer, c'est du plug en play dans ton cas ; seul le wifi demandera une configuration.
Donc si tu n'as rien modifié, ça devrait marcher.
Avais-tu essayer la distribution avec un Live CD ou USB et si oui qu'en était-il de la connexion internet ?
Note : dans SliTaz 4.0, l'icone de connexion, en haut à droite de l'écran, indique par défaut l'état de la connexion wifi ; clique dessus puis choisi Nom = Eth0 et regarde si tu vois une activité reçu/envoyé.
Offline
J'avais essayé avec un live-cd et ça ne marchait pas non plus. Aucune activité pour eth0.
La seule chose que j'ai modifié tout à l'heure dans le tazpanel : le nom du réseau sfr et j'ai rentré la clé wifi. Il ne se passe rien. Bon ben je vais attendre encore du coup.
Merci et bonne journée !
Offline
Bonjour,
après une autre réinstallation, j'arrive enfin à me connecter un peu par câble. Sauf que je ne peux pas vraiment surfer. Je n'ai plus la croix rouge sur l'icône wifi.
Je pense que je vais essayer de tout refaire pour voir si ça marche.
Je me retournerai vers vous en cas de besoin.
Merci à tous d'être intervenus.
Offline
Voici les rapports ; si quelqu'un a une idée.
root@slitaz:/home/tux# tazhw detect-pci --get-firmware
Detected PCI devices Kernel modules
================================================================================
> Module in use: intel_agp
> Module in use: snd_intel8x0
> Module in use: snd_intel8x0m
> Module in use: radeon
> Module in use: b44
> Module in use: ipw2200
> Module in use: yenta_socket
================================================================================
root@slitaz:/home/tux# /etc/init.d/network.sh restart
Stopping all interfaces
ifconfig: SIOCGIFFLAGS: No such device
Killing all daemons
killall: udhcpc: no process killed
wlan0 No such device
Configuring static IP on eth0: 192.168.0.6...
root@slitaz:/home/tux# lspci | grep -i network
02:04.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
root@slitaz:/home/tux# tazhw detect-pci
Detected PCI devices Kernel modules
================================================================================
> Module in use: intel_agp
> Module in use: snd_intel8x0
> Module in use: snd_intel8x0m
> Module in use: radeon
> Module in use: b44
> Module in use: ipw2200
> Module in use: yenta_socket
================================================================================
root@slitaz:/home/tux# tazpkg get-install get-wifi-firmware
wget: bad address 'mirror.slitaz.org'
wget: bad address 'mirror.slitaz.org'
/usr/bin/tazpkg: line 2958: can't open /var/cache/tazpkg/4.0/packages/get-wifi-firmware-2.0.tazpkg: no such file
/usr/bin/tazpkg: .: line 2958: can't open '/tmp/tazpkg-4911/30143/receipt'
root@slitaz:/home/tux# ls /usr/bin/get-*-firmware
ls: /usr/bin/get-*-firmware: No such file or directory
root@slitaz:/home/tux# get-ipw2200-firmware
sh: get-ipw2200-firmware: not found
root@slitaz:/home/tux#
Il semble que sixofeight ait raison mais bon, j'y arrive pas !
Offline
Essayes :
# echo 'nameserver 208.67.220.220' >> /etc/resolv.conf
# echo 'nameserver 208.67.222.222' >> /etc/resolv.conf
# tazpkg get-install get-wifi-firmware
# get-ipw2200-firmware
Offline
Voici la réponse. ça ne marche pas.
root@slitaz:/home/tux# echo 'nameserver 208.67.220.220' >> /etc/resolv.conf
root@slitaz:/home/tux# echo 'nameserver 208.67.222.222' >> /etc/resolv.conf
root@slitaz:/home/tux# tazpkg get-install get-wifi-firmware
Connecting to mirror.slitaz.org (37.187.4.13:80)
Connecting to mirror.switch.ch (130.59.10.36:80)
packages.desc 100% |*******************************| 349k 00:00:00 ETA
Connecting to mirror.slitaz.org (212.83.135.187:80)
Connecting to download.tuxfamily.org (212.85.158.13:80)
packages.md5 100% |*******************************| 195k 00:00:00 ETA
Connecting to mirror.slitaz.org (188.165.229.172:80)
packages.txt 100% |*******************************| 274k --:--:-- ETA
Connecting to mirror.slitaz.org (37.187.4.13:80)
Connecting to mirror.switch.ch (130.59.10.36:80)
packages.list 100% |*******************************| 61722 --:--:-- ETA
Connecting to mirror.slitaz.org (212.83.135.187:80)
Connecting to download.tuxfamily.org (212.85.158.13:80)
packages.equiv 100% |*******************************| 4116 --:--:-- ETA
Connecting to mirror.slitaz.org (188.165.229.172:80)
files.list.lzma 100% |*******************************| 1817k 00:00:00 ETA
Connecting to mirror.slitaz.org (37.187.4.13:80)
Connecting to mirror.switch.ch (130.59.10.36:80)
mirrors 100% |*******************************| 983 --:--:-- ETA
================================================================================
La dernière liste des paquets est prête à être utilisée. Notez qu'à la prochaine
recharge, une liste des différences sera affichée pour vous montrer les nouveaux
paquets et les mises à jour disponibles.
Connecting to mirror.slitaz.org (212.83.135.187:80)
Connecting to download.tuxfamily.org (212.85.158.13:80)
get-wifi-firmware-2. 100% |*******************************| 5364 --:--:-- ETA
Installation de: get-wifi-firmware
================================================================================
Copie de get-wifi-firmware... [ OK ]
Extraction de get-wifi-firmware... [ OK ]
Extraction du pseudo fs...(lzma) [ OK ]
Installation de get-wifi-firmware... [ OK ]
Suppression des fichiers temporaires... [ OK ]
Connecting to www.intellinuxwireless.org (192.198.165.191:80)
Connecting to corpredirect.intel.com (5.178.43.27:80)
Connecting to wireless.kernel.org (198.145.29.83:80)
wget: not an http or ftp url: https://wireless.kernel.org/en/users/Drivers/iwlwifi/?n=Downloads
Connecting to www.intellinuxwireless.org (192.198.165.191:80)
Connecting to corpredirect.intel.com (5.178.43.8:80)
Connecting to wireless.kernel.org (198.145.29.83:80)
wget: not an http or ftp url: https://wireless.kernel.org/en/users/Drivers/iwlwifi/iwlwifi/downloads/iwlwifi-3945-ucode-.tgz
Could not download iwlwifi-3945-ucode-.tgz. Exiting.
Connecting to www.intellinuxwireless.org (192.198.165.191:80)
Connecting to corpredirect.intel.com (5.178.43.27:80)
Connecting to wireless.kernel.org (198.145.29.83:80)
wget: not an http or ftp url: https://wireless.kernel.org/en/users/Drivers/iwlwifi/?n=Downloads
Connecting to www.intellinuxwireless.org (192.198.165.191:80)
Connecting to corpredirect.intel.com (5.178.43.8:80)
Connecting to wireless.kernel.org (198.145.29.83:80)
wget: not an http or ftp url: https://wireless.kernel.org/en/users/Drivers/iwlwifi/iwlwifi/downloads/iwlwifi-4965-ucode-.tgz
Could not download iwlwifi-4965-ucode-.tgz. Exiting.
Connecting to www.intellinuxwireless.org (192.198.165.191:80)
Connecting to corpredirect.intel.com (5.178.43.27:80)
Connecting to wireless.kernel.org (198.145.29.83:80)
wget: not an http or ftp url: https://wireless.kernel.org/en/users/Drivers/iwlwifi/?n=Downloads
Connecting to www.intellinuxwireless.org (192.198.165.191:80)
Connecting to corpredirect.intel.com (5.178.43.8:80)
Connecting to wireless.kernel.org (198.145.29.83:80)
wget: not an http or ftp url: https://wireless.kernel.org/en/users/Drivers/iwlwifi/iwlwifi/downloads/iwlwifi-5000-ucode-.tgz
Could not download iwlwifi-5000-ucode-.tgz. Exiting.
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
- 100% |*******************************| 930 --:--:-- ETA
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
RT61_Firmware_V1.2.z 100% |*******************************| 13937 --:--:-- ETA
Archive: RT61_Firmware_V1.2.zip
creating: RT61_Firmware_V1.2/
inflating: RT61_Firmware_V1.2/rt2561.bin
inflating: RT61_Firmware_V1.2/rt2561s.bin
inflating: RT61_Firmware_V1.2/rt2661.bin
inflating: RT61_Firmware_V1.2/LICENSE.ralink-firmware.txt
Packing : rt61-firmware-1.2
================================================================================
Création de la liste des fichiers... [ OK ]
Création de la somme md5 des fichiers... [ OK ]
Compression du système de fichiers... [ OK ]
Mise à jour des tailles dans la recette... [ OK ]
Création de l'archive cpio complète... [ OK ]
Restoration de l'arbre original du paquet... [ OK ]
================================================================================
Paquet rt61-firmware-1.2 compressé avec succès.
Taille : 8.0K rt61-firmware-1.2.tazpkg
Installation de: rt61-firmware
================================================================================
Copie de rt61-firmware... [ OK ]
Extraction de rt61-firmware... [ OK ]
Extraction du pseudo fs...(lzma) [ OK ]
Installation de rt61-firmware... [ OK ]
Suppression des fichiers temporaires... [ OK ]
================================================================================
rt61-firmware (1.2) est installé.
just install firmare: yes
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
- 100% |*******************************| 934 --:--:-- ETA
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
RT71W_Firmware_V1.8. 100% |*******************************| 2679 --:--:-- ETA
Archive: RT71W_Firmware_V1.8.zip
creating: RT71W_Firmware_V1.8/
inflating: RT71W_Firmware_V1.8/rt73.bin
inflating: RT71W_Firmware_V1.8/LICENSE.ralink-firmware.txt
Packing : rt73-firmware-1.8
================================================================================
Création de la liste des fichiers... [ OK ]
Création de la somme md5 des fichiers... [ OK ]
Compression du système de fichiers... [ OK ]
Mise à jour des tailles dans la recette... [ OK ]
Création de l'archive cpio complète... [ OK ]
Restoration de l'arbre original du paquet... [ OK ]
================================================================================
Paquet rt73-firmware-1.8 compressé avec succès.
Taille : 4.0K rt73-firmware-1.8.tazpkg
Installation de: rt73-firmware
================================================================================
Copie de rt73-firmware... [ OK ]
Extraction de rt73-firmware... [ OK ]
Extraction du pseudo fs...(lzma) [ OK ]
Installation de rt73-firmware... [ OK ]
Suppression des fichiers temporaires... [ OK ]
================================================================================
rt73-firmware (1.8) est installé.
just install firmare: yes
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
- 100% |*******************************| 926 --:--:-- ETA
Connecting to archlinux.c3sl.ufpr.br (200.236.31.1:80)
RT2870_Firmware_V8.z 100% |*******************************| 2641 --:--:-- ETA
Archive: RT2870_Firmware_V8.zip
inflating: RT2870_Firmware_V8/LICENSE.ralink-firmware.txt
inflating: RT2870_Firmware_V8/rt2870.bin
Packing : rt2870usb-firmware-8
================================================================================
Création de la liste des fichiers... [ OK ]
Création de la somme md5 des fichiers... [ OK ]
Compression du système de fichiers... [ OK ]
Mise à jour des tailles dans la recette... [ OK ]
Création de l'archive cpio complète... [ OK ]
Restoration de l'arbre original du paquet... [ OK ]
================================================================================
Paquet rt2870usb-firmware-8 compressé avec succès.
Taille : 4.0K rt2870usb-firmware-8.tazpkg
Installation de: rt2870usb-firmware
================================================================================
Copie de rt2870usb-firmware... [ OK ]
Extraction de rt2870usb-firmware... [ OK ]
Extraction du pseudo fs...(lzma) [ OK ]
Installation de rt2870usb-firmware... [ OK ]
Suppression des fichiers temporaires... [ OK ]
================================================================================
rt2870usb-firmware (8) est installé.
just install firmare: yes
================================================================================
get-wifi-firmware (2.0) est installé.
root@slitaz:/home/tux# get-ipw2200-firmware
Connecting to ipw2200.sourceforge.net (216.34.181.96:80)
- 100% |*******************************| 14411 --:--:-- ETA
wget: bad address 'bughost.org'
Could not download ipw2200-fw-3.1.tgz. Exiting.
root@slitaz:/home/tux#
Offline
et maintenant j'ai :
root@slitaz:/home/tux# get-ipw2200-firmware
Connecting to ipw2200.sourceforge.net (216.34.181.96:80)
- 100% |*******************************| 14411 --:--:-- ETA
ipw2200-firmware package is already installed.
root@slitaz:/home/tux#
Merci quand même.
Offline
Until you get a better reply..
The Firmware is installed...now (as root) try again
modprobe -r ipw2200
than
modprobe ipw2200
when done check with ifconfig -a if the device shows up
if not check with dmesg | grep -i firmware if there is the same issue like before.
(ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
ipw2200: Unable to load firmware: -2)
Maybe you should check which version of the ipw2200 driver is included in Slitaz4.
try modinfo ipw2200
Hopefully it will display the version number,compare it with the firmware link at
this page:
https://wireless.wiki.kernel.org/en/users/drivers/ipw2200
it could be that you need an older Package.
good luck
==============================================
2nd idea to troubleshoot this.
boot another live Linux...if the wifi is working, check wich module and firmware Files are being loaded...compare the md5sum of the firmware files, if they are different, copy them into Slitaz
(the firmware only)
Offline
HI ! Thank you for this answer, I'll try as soon as I can.
Offline
Bonjour sd,
Me revoilà. Je vois que tu as bien avancé :
[c]Connecting to download.tuxfamily.org (212.85.158.13:80)
get-wifi-firmware-2. 100% |*******************************| 5364 --:--:-- ETA[/c]
Ta connexion ethernet fonctionne.
j'arrive enfin à me connecter un peu par câble. Sauf que je ne peux pas vraiment surfer.
Qu'entends-tu par me connecter un peu par le câble et je ne peux pas vraiment surfer ?
La version de Midori dans SliTaz 4.0 est dépassée et ne permet effectivement plus grand chose. Si tu as assez de mémoire (combien au fait ?) tu pourras installer un autre navigateur.
ipw2200-firmware package is already installed.
Parfait, le driver de ta carte wifi est installé ; il ne reste plus qu'à faire la configuration.
Tout d'abord, assure-toi que ta carte wifi et en service ; sur pas mal de PC, il y a un bouton ON/OFF.
Ensuite, rendez-vous dans TazPanel > Network > Wireless
[*]Clique sur [Démarrer] ; la liste des wifi détectés devrait s'afficher.
[*]Sélectionne ta box.
[*]Dans l'encadré Connexion tu devrais voir apparaître le nom de ta box (Nom du réseau (EESID)).
[*]Entre ta clé wifi dans le champ Mot de passe (Clé Wifi)
[*]Lance la procédure de reconnaissance d'une nouvelle connexion wifi sur ta box et clique sur [Configurer]
Maintenant, dans l'encadré Fichier de configuration, tu devrais voir [c]WIFI="yes"[/c]
[*]Ouvre un terminal en tant que root et lance la commande
/etc/init.d/network.sh restart
Ta connexion ethernet ne devrait plus fonctionner mais le wifi devrait être OK.
Si ça bloque quelque part, dis-nous à quel niveau.
Pour revenir à la connexion ethernet :
[*]TazPanel > Network > Wireless
[*][Édition manuelle]
[*][c]WIFI="no"[/c]
[*][Enregistrer]
[*]Dans un terminal "root" : [c]/etc/init.d/network.sh restart[/c]
Offline
Merci beaucoup, ça marche bien maintenant. Je crois qu'il fallait faire les choses au fur et à mesure et attendre que l'ordinateur s'imprègne des changements.
Bonne continuation.
Offline
Pages: 1
[ Generated in 0.018 seconds, 7 queries executed - Memory usage: 1.66 MiB (Peak: 1.77 MiB) ]