SliTaz Forum
You are not logged in.
Thats from CTK-Arch - boots wih all my devices
# USB Host Controller Drivers
#
CONFIG_USB_C67X00_HCD=m
CONFIG_USB_XHCI_HCD=m
# CONFIG_USB_XHCI_HCD_DEBUGGING is not set
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
CONFIG_USB_OXU210HP_HCD=m
CONFIG_USB_ISP116X_HCD=m
CONFIG_USB_ISP1760_HCD=m
CONFIG_USB_ISP1362_HCD=m
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_HCD_SSB is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
CONFIG_USB_UHCI_HCD=m
CONFIG_USB_U132_HCD=m
CONFIG_USB_SL811_HCD=m
CONFIG_USB_SL811_CS=m
CONFIG_USB_R8A66597_HCD=m
CONFIG_USB_WHCI_HCD=m
CONFIG_USB_HWA_HCD=m
Offline
@ernia I changed to this thread
what I should have done is to notice all the changes I did - but it is too late. Mainly I did no change much - I just did some from =y to =m, where I thought, that this is not necessary to be built in the kernel
Offline
i'm cooking it
Offline
Kernel: arch/x86/boot/bzImage is ready (#3)
scripts/kconfig/conf --silentoldconfig Kconfig
.config:1458:warning: symbol value 'm' invalid for MD
.config:1706:warning: symbol value 'm' invalid for VIA_RHINE_MMIO
*
* Restart config...
*
*
* Processor type and features
*
Tickless System (Dynamic Ticks) (NO_HZ) [Y/n/?] y
High Resolution Timer Support (HIGH_RES_TIMERS) [N/y/?] n
Symmetric multi-processing support (SMP) [Y/n/?] y
Enable MPS table (X86_MPPARSE) [Y/n/?] y
Support for big SMP systems with more than 8 CPUs (X86_BIGSMP) [N/y/?] n
Support for extended (non-PC) x86 platforms (X86_EXTENDED_PLATFORM) [Y/n/?] y
Intel MID platform support (X86_WANT_INTEL_MID) [Y/n/?] y
Moorestown MID platform (X86_MRST) [N/y/?] n
RDC R-321x SoC (X86_RDC321X) [N/y/?] n
Support non-standard 32-bit SMP architectures (X86_32_NON_STANDARD) [N/y/?] n
Eurobraille/Iris poweroff module (X86_32_IRIS) [N/m/y/?] n
Single-depth WCHAN output (SCHED_OMIT_FRAME_POINTER) [Y/n/?] y
Memtest (MEMTEST) [N/y/?] n
Processor family
> 1. 386 (M386)
2. 486 (M486)
3. 586/K5/5x86/6x86/6x86MX (M586)
4. Pentium-Classic (M586TSC)
5. Pentium-MMX (M586MMX)
6. Pentium-Pro (M686)
7. Pentium-II/Celeron(pre-Coppermine) (MPENTIUMII)
8. Pentium-III/Celeron(Coppermine)/Pentium-III Xeon (MPENTIUMIII)
9. Pentium M (MPENTIUMM)
10. Pentium-4/Celeron(P4-based)/Pentium-4 M/older Xeon (MPENTIUM4)
11. K6/K6-II/K6-III (MK6)
12. Athlon/Duron/K7 (MK7)
13. Opteron/Athlon64/Hammer/K8 (MK8)
14. Crusoe (MCRUSOE)
15. Efficeon (MEFFICEON)
16. Winchip-C6 (MWINCHIPC6)
17. Winchip-2/Winchip-2A/Winchip-3 (MWINCHIP3D)
18. AMD Elan (MELAN)
19. GeodeGX1 (MGEODEGX1)
20. Geode GX/LX (MGEODE_LX)
21. CyrixIII/VIA-C3 (MCYRIXIII)
22. VIA C3-2 (Nehemiah) (MVIAC3_2)
23. VIA C7 (MVIAC7)
24. Core 2/newer Xeon (MCORE2)
25. Intel Atom (MATOM)
choice[1-25]: 1
Generic x86 support (X86_GENERIC) [Y/n/?] y
PentiumPro memory ordering errata workaround (X86_PPRO_FENCE) [Y/n/?] y
HPET Timer Support (HPET_TIMER) [N/y/?] n
Maximum number of CPUs (NR_CPUS) [8] 8
SMT (Hyperthreading) scheduler support (SCHED_SMT) [Y/n/?] y
Multi-core scheduler support (SCHED_MC) [Y/n/?] y
Fine granularity task level IRQ time accounting (IRQ_TIME_ACCOUNTING) [N/y/?] n
Preemption Model
> 1. No Forced Preemption (Server) (PREEMPT_NONE)
2. Voluntary Kernel Preemption (Desktop) (PREEMPT_VOLUNTARY)
3. Preemptible Kernel (Low-Latency Desktop) (PREEMPT)
choice[1-3]: 1
Reroute for broken boot IRQs (X86_REROUTE_FOR_BROKEN_BOOT_IRQS) [N/y/?] n
Machine Check / overheating reporting (X86_MCE) [Y/n/?] y
Intel MCE features (X86_MCE_INTEL) [Y/n/?] y
AMD MCE features (X86_MCE_AMD) [Y/n/?] y
Support for old Pentium 5 / WinChip machine checks (X86_ANCIENT_MCE) [N/y/?] n
Machine check injector support (X86_MCE_INJECT) [N/m/y/?] n
Toshiba Laptop support (TOSHIBA) [M/n/y/?] m
Dell laptop support (I8K) [M/n/y/?] m
Enable X86 board specific fixups for reboot (X86_REBOOTFIXUPS) [Y/n/?] y
/dev/cpu/microcode - microcode support (MICROCODE) [M/n/y/?] m
Intel microcode patch loading support (MICROCODE_INTEL) [Y/n/?] (NEW) aborted!
Console input/output is redirected. Run 'make oldconfig' to update configuration.
make[2]: *** [silentoldconfig] Error 1
make[1]: *** [silentoldconfig] Error 2
make: *** No rule to make target [c]include/config/auto.conf', needed by[/c]include/config/kernel.release'. Stop.
make: *** Waiting for unfinished jobs....
make[1]: Nothing to be done for `relocs'.
mv: can't rename 'arch/x86/boot/bzImage': No such file or directory
Error : /home/slitaz/wok/linux/install/lib/modules/3.2-slitaz does not exist.
Offline
sorry - I took this option from a request in the forum - in 2.6. Kernels it was just necessary to set CONFIG_MICROCODE=m - from 2.6.28 up you need to select minimum one vendor - so I think we should go here for:
line 357 CONFIG_MICROCODE=m
line 358 CONFIG_MICROCODE_INTEL=y
line 359 CONFIG_MICROCODE_AMD=y
line 360 CONFIG_MICROCODE_OLD_INTERFACE=y
Offline
and sorry just saw the warnings - was to early.. - theese should go to
line 1458 CONFIG_MD=y
line 1706 # CONFIG_VIA_RHINE_MMIO is not set
Offline
ok, i'll do this evening
Offline
thx - I just included all the changes, so you dont have to do it
Offline
i already did the changes you said, it's cooking now
Offline
[c]Kernel: arch/x86/boot/bzImage is ready (#3)
scripts/kconfig/conf --silentoldconfig Kconfig
*
* Restart config...
*
*
* Serial ATA and Parallel ATA drivers
*
Serial ATA and Parallel ATA drivers (ATA) [M/n/y/?] m
Verbose ATA error reporting (ATA_VERBOSE_ERROR) [Y/n/?] y
ATA ACPI Support (ATA_ACPI) [Y/n/?] y
SATA Port Multiplier support (SATA_PMP) [Y/n/?] y
*
* Controllers with non-SFF native interface
*
AHCI SATA support (SATA_AHCI) [M/n/?] m
Platform AHCI SATA support (SATA_AHCI_PLATFORM) [N/m/?] n
Initio 162x SATA support (SATA_INIC162X) [N/m/?] n
ACard AHCI variant (ATP 8620) (SATA_ACARD_AHCI) [N/m/?] n
Silicon Image 3124/3132 SATA support (SATA_SIL24) [N/m/?] n
ATA SFF support (ATA_SFF) [Y/n/?] y
*
* SFF controllers with custom DMA interface
*
Pacific Digital ADMA support (PDC_ADMA) [N/m/?] n
Pacific Digital SATA QStor support (SATA_QSTOR) [N/m/?] n
Promise SATA SX4 support (Experimental) (SATA_SX4) [N/m/?] n
ATA BMDMA support (ATA_BMDMA) [Y/n/?] y
*
* SATA SFF controllers with BMDMA
*
Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support (ATA_PIIX) [M/n/?] m
Marvell SATA support (SATA_MV) [N/m/?] (NEW) aborted!
Console input/output is redirected. Run 'make oldconfig' to update configuration.[/c]
what do you want to do with Marvell SATA ?
i think that Serial ATA and Parallel ATA drivers (ATA) [M/n/y/?] m should be yes if you want to boot.
Offline
one more time sorry - I forgot to remove a # - it was
#CONFIG_SATA_MV=m
should be
CONFIG_SATA_MV=m
let us try like this - it works without problems in CTKatch, I do not want to make to much changes in the kernel - only necessary ones - like I have no idea, why in original kernel
CONFIG_PATA_SCH=y
CONFIG_PATA_SIS=y
are set and all the rest not - so I just set them to =m
Offline
[c]INSTALL /home/slitaz/wok/linux/install/lib/firmware/kaweth/trigger_code_fix.bin
DEPMOD 3.2-slitaz
CHK include/linux/version.h
make[1]: Nothing to be done for[/c]
relocs'.
/home/slitaz/wok/linux/source/linux-3.2.40/scripts/Makefile.headersinst:14: /home/slitaz/wok/linux/source/linux-3.2.40/include/linux/Kbuild: No such file or directory
make[2]: *** No rule to make target `/home/slitaz/wok/linux/source/linux-3.2.40/include/linux/Kbuild'. Stop.
make[1]: *** [linux] Error 2
make[1]: *** Waiting for unfinished jobs....
INSTALL include/drm (13 files)
INSTALL include/mtd (5 files)
INSTALL include/asm-generic (34 files)
make: *** [headers_install] Error 2
Starting gztazmod.sh to build compressed kernel modules...
Searching all modules to compress them... [ OK ]
Building tmp.dep... [ OK ]
Destroying modules.dep... [ OK ]
Removing tmp.dep to modules.dep... [ OK ]
Kernel modules 3.2-slitaz are ready.
Starting gztazmod.sh to build compressed kernel modules...
Searching all modules to compress them... [ OK ]
Building tmp.dep... [ OK ]
Destroying modules.dep... [ OK ]
Removing tmp.dep to modules.dep... [ OK ]
Kernel modules 3.2-slitaz are ready.
===================================================================================================================================================================================================================
Build dependencies to remove: 7
Removing: curl git libcurl libidn uclibc-cross-compiler-x86_64 wget xz
Pack: linux 3.2.40
===================================================================================================================================================================================================================
Executing: genpkg_rules
find: /home/slitaz/wok/linux/install/lib/modules/*-slitaz/kernel/drivers/usb/storage/uas.ko.xz: No such file or directory
find: /home/slitaz/wok/linux/install/lib/modules/*-slitaz/kernel/drivers/ide/ide-cs.ko.xz: No such file or directory
find: /home/slitaz/wok/linux/install/lib/modules/*-slitaz/kernel/net/ipv4/inet_lro.ko.xz: No such file or directory
cook dahdi-linux
cook libcap
Checking for modules selected in .config but not in linux-* pkgs
======================================================================
Orphan module: cpuid.ko.xz
Orphan module: microcode.ko.xz
Orphan module: msr.ko.xz
Orphan module: pktcdvd.ko.xz
Orphan module: i2c-designware-core.ko.xz
Orphan module: st_drv.ko.xz
Orphan module: sd_mod.ko.xz
Orphan module: scsi_mod.ko.xz
Orphan module: sr_mod.ko.xz
Orphan module: ftdi-elan.ko.xz
Orphan module: usb-storage.ko.xz
Orphan module: ehci-hcd.ko.xz
Orphan module: cpufreq_stats.ko.xz
Orphan module: cpufreq_userspace.ko.xz
Orphan module: hv_vmbus.ko.xz
Orphan module: cdrom.ko.xz
Orphan module: ata_generic.ko.xz
Orphan module: sata_sis.ko.xz
Orphan module: sata_sil.ko.xz
Orphan module: ata_piix.ko.xz
Orphan module: pata_sch.ko.xz
Orphan module: pata_legacy.ko.xz
Orphan module: pata_acpi.ko.xz
Orphan module: pata_sis.ko.xz
Orphan module: sata_nv.ko.xz
Orphan module: sata_mv.ko.xz
Orphan module: libahci.ko.xz
Orphan module: sata_via.ko.xz
Orphan module: ahci.ko.xz
Orphan module: libata.ko.xz
Orphan module: arcnet.ko.xz
Orphan module: com20020.ko.xz
Orphan module: r8169.ko.xz
Orphan module: via-rhine.ko.xz
Orphan module: 8390.ko.xz
Orphan module: ne2k-pci.ko.xz
Orphan module: atl1.ko.xz
Orphan module: acenic.ko.xz
Orphan module: tlan.ko.xz
Orphan module: sundance.ko.xz
Orphan module: pcnet32.ko.xz
Orphan module: e1000e.ko.xz
Orphan module: e100.ko.xz
Orphan module: winbond-840.ko.xz
Orphan module: xircom_cb.ko.xz
Orphan module: de4x5.ko.xz
Orphan module: dmfe.ko.xz
Orphan module: forcedeth.ko.xz
Orphan module: qla3xxx.ko.xz
Orphan module: sis900.ko.xz
Orphan module: tun.ko.xz
Orphan module: xfrm_user.ko.xz
Orphan module: xfrm_ipcomp.ko.xz
Orphan module: af_key.ko.xz
Orphan module: ipip.ko.xz
Orphan module: xfrm4_mode_transport.ko.xz
Orphan module: xfrm4_mode_tunnel.ko.xz
Orphan module: xfrm4_tunnel.ko.xz
Orphan module: esp4.ko.xz
Orphan module: xfrm4_mode_beet.ko.xz
Orphan module: tunnel4.ko.xz
Orphan module: ipcomp.ko.xz
Orphan module: ah4.ko.xz
Orphan module: i2c-designware-core.ko.xz
Orphan module: st_drv.ko.xz
Orphan module: ftdi-elan.ko.xz
Orphan module: hv_vmbus.ko.xz
Orphan module: virtio_console.ko.xz
Orphan module: arcnet.ko.xz
Orphan module: com20020.ko.xz
======================================================================
Check linux/tmp/unpackaged-modules-3.2.40.list for mod path
Copying receipt... [ Done ]
Creating the list of files... [ Done ]
Executing strip on all files... [ Done ]
Creating md5sum of files... [ Done ]
Compressing the fs... [ Done ]
Updating receipt sizes... [ Done ]
Creating full cpio archive... [ Done ]
Restoring original package tree... [ Done ]
QA: Checking for empty package... [ Done ]
Removing old: linux-3.2.40.tazpkg [ Done ]
===================================================================================================================================================================================================================
Package: linux-3.2.40.tazpkg
Summary for: linux 3.2.40
===================================================================================================================================================================================================================
Source dir : 1.0G
Src file : linux-3.2.tar.xz
Src size : 62.1M
Produced : 75.9M
Packed : 8.4M
Compressed : 5.5M
Files : 312
Cook time : 8580s ~ 143m
Cook date : 2013-03-14 22:50
Host arch : i486`
i got an error in the install phase and there are lot of modules which should be included in a linux-something package. let me know what you want to do.
Offline
Ernia excuse me - I should not have done like this - I have to do this myself - I hope I will have time in July / August to test
lets do just the necessary changes - from the actual rolling with 3.2.40 kernel-config:
line 126 CONFIG_RT_GROUP_SCHED=y
line 337 CONFIG_SCHED_SMT=y
line 357 CONFIG_MICROCODE=m
line 358 CONFIG_MICROCODE_INTEL=y
line 359 CONFIG_MICROCODE_AMD=y
line 360 CONFIG_MICROCODE_OLD_INTERFACE=y
line 361 CONFIG_X86_MSR=m
line 1540 CONFIG_PATA_ACPI=y
line 1541 CONFIG_ATA_GENERIC=y
line 1542 CONFIG_PATA_LEGACY=y
line 3807 CONFIG_USB_EHCI_ROOT_HUB_TT=y
line 3808 CONFIG_USB_EHCI_TT_NEWSCHED=y
if it is not to much work for you, it would be nice to pastbin this nonworking kernel, so I can check myself....
Offline
there is still something wrong, but I do not want to use always ernias time to make a different kernel - I have to do it myself.
But I am not able - perhaps somebody can tell me what I am doing wrong:
just following: http://doc.slitaz.org/en:guides:kernel
root@slitaz:/usr/src# ls -l /usr/src
total 12
drwxr-xr-x 3 root root 4096 Mar 18 11:53 kernel-patches
lrwxrwxrwx 1 root root 12 Mar 18 12:49 linux -> linux-3.2.40
drwxr-xr-x 2 root root 4096 Mar 18 11:53 linux-3.2.40
drwxr-xr-x 12 root root 4096 Mar 18 12:37 linux-3.2-slitaz
root@slitaz:/usr/src# cd linux
root@slitaz:/usr/src/linux-3.2.40# ls
aufs3-base.patch
aufs3-loopback.patch
aufs3-proc_map.patch
aufs3-standalone.patch
bootloader.sh
buildtaz
channel-negative-one-maxim.patch
config
config64
gztazmod.sh
linux-diff.u
linux-freeinitrd.u
linux-header.u
list_modules.sh
mac80211.compat08082009.wl_frag+ack_v1.patch
make-tazpkg.u
patches
url
root@slitaz:/usr/src/linux-3.2.40# make menuconfig
make: *** No rule to make target `menuconfig'. Stop.
what is wrong, that I get all the time "make: *** No rule to make target `menuconfig'. Stop."
what I recogniced is, that "tazpkg get-install slitaz-toolchain" does not install the headers - so afterwards I installed linux-api-headers and linux-module-headers
root@slitaz:/usr/src# tazpkg search headers
Search result for: headers
================================================================================
Installed packages
================================================================================
linux-api-headers 3.2.40 development
linux-module-headers 3.2.40 development
================================================================================
2 installed packages found for: headers
but still I get the same error - it drives me crazy, that I am not able to make a kernel
EDIT: the headers are installed when running "tazpkg -gi slitaz-toolchain" from fresh iso
Offline
tried it from a new iso - here is one eorror:
root@slitaz:/home/tux# /usr/bin/get-linux-source
Connecting to www.kernel.org (198.145.20.140:80)
wget: not an http or ftp url: https://www.kernel.org/pub/linux/kernel/v3.0/linux-3.2.tar.xz
Connecting to linux-kernel.uio.no (128.39.3.170:80)
Connecting to linux-kernel.uio.no (128.39.3.170:80)
linux-3.2.tar.xz 100% |*******************************| 63540k 0:00:00 ETA
tar: invalid magic
tar: short read
/usr/bin/get-linux-source: line 44: can't open slitaz/patches: no such file
cp: can't stat 'slitaz/config': No such file or directory
Offline
hi Tom,
first of all you don't use my time but almost only my cpu time :-)
please forgive me if i tell you something wrong but i'm testing my wine from the pinot vineyard, and i'm testing a little bit of home made salami too, so i'm getting a little bit unreliable :-)
linux-source is broken in cooking (or rolling, i can't tell the difference), so i use wok (cookbook) and edit /home/slitaz/wok/linux/stuff/linux-slitaz.config to fit your instructions then i cook it with
[c]cooker pkg linux[/c]
if you want to experiment when you have cooked it first time you will have /home/slitaz/wok/linux/source/linux[something]/.config (i don't have linux[something] anymore because i tested your tar error and the folder has disapperead). if you install ncurses you can change to /home/slitaz/wok/linux/source/linux[something]/ and
[c]make menuconfig[/c]
once you have done your changes you can copy .config to /home/slitaz/wok/linux/stuff/linux-slitaz.config and try again to cook it.
when you have cooked it you should cook packages wanting linux, which are almost all linux-* packages and contains linux modules.
i use this line:
[c]for i in $(grep 'WANTED="linux"' */receipt | grep -v 64 | cut -d \/ -f 1); do cooker pkg $i; done[/c]
run the command from the wok directory.
warnings about orphaned modules are telling you that you built modules which are not contained in a linux-*package so you should write a receipt for a package containg these modules.
after have builded linux-* packages you should
[c]cook linux --pack[/c]
which repack linux without rebuilding it and check again missing modules.
please, there is something wrong with cook getting https sources, i did not noticed it because i alredy had sources in /home/slitaz/src, so as a workaround you better manually download linux-3.2.tar.xz and patch-3.2.40.xz and put them in /home/slitaz/src.
Offline
I forgive you evrything and I hope your vine and your salami tasted well....
and I am happy, that I am not totally stupid - I will try.....
Offline
I come to the point "cooker pkg linux"
here I get the error
Connecting to www.kernel.org (198.145.20.140:80)
wget: not an http or ftp url: https://www.kernel.org/pub/linux/kernel/v3.0/linux-3.2.tar.xz
ERROR: wget http://www.kernel.org/pub/linux/kernel/v3.0/linux-3.2.tar.xz
Build dependencies to remove: 5
Removing: curl git uclibc-cross-compiler-x86_64 wget xz
ERROR: cook failed
Debug information
================================================================================
Cook date: 2013-03-21 19:07
ERROR: cook failed
================================================================================
wget and https does not fit together - do I have to do it manually_ and where to put?
Offline
I think, we have to change to ftp!!!!
wget ftp://ftp.kernel.org/pub/linux/kernel/v3.0/linux-3.2.tar.xz
works fine - I think, it has to be changed also in the linux reciept
http://hg.slitaz.org/wok/file/c0b3f72ff53d/linux/receipt
Offline
sorry for i could not able to make new topics.
i was using lates slitaz stable version, and having problem with gparted.
i already install dosfstool and mtool.
slitaz gpart having a problem, when formating usb partition as fat32.
now i am trying to install gpart 0.14.1 from cook, but gpart wont run on stable slitaz4.0.
please help me i need gparted atleast version 0.14.1 or maybe 0.15 tazpackage for the stable slitaz.
help ?
Offline
finally I checked it, but there are some errors in the doku - at least in rolling:
1) I had to run "cook setup --wok" 2 times until I have a wok directory in /home/slitaz - after the first time, there is only cooking and src directory
2) there must be a reboot inbetween and you shoud not do anything else - first I set up cooker after the first "cook setup --wok" and here was all the time lots of errors, when I run "cook linux"
3) I get lots of warnings when cooking the kernel with the original rolling-config - see attachment - when I look into the log of cooker - http://cook.slitaz.org/cooker.cgi?pkg=linux there are no warnings.
Whats still wrong with my cook environment
Thomas
Offline
I have some time left, so I thought maybe have a look to the kernel - first thing I did was to check http://cook.slitaz.org/cooker.cgi?pkg=linux and now there are the same errors, I got all the time.
So I think, we could change to my config, that pcoduces the same error, but solves the ide bug - config is attached.
But my question is: where the errors now come from? did I miss some changes? - those I find
http://hg.slitaz.org/wok/rev/416fab3c90c0
http://hg.slitaz.org/wok/rev/a62a3bf42fb0
Offline
Hi Tom,
In the attached config file (linux.slitaz.config.txt) I can see the following:
# CONFIG_IDE is not set
I think your intention was to enable the IDE support and we need to use the 3.2.40-new.txt config file you uploaded in a previous post (and we could build that cleanly).
Please clarify so that we can proceed with the correct config file.
Regards,
Arun
Offline
Here's a revision to the above post:
I did reproduce the issue of ...No such file or directory and orphan modules with 3.2.40-new.txt config file.
Here are a few questions:
From the number of orphan module errors it seems a lot of modules have been enabled. Do we really need all of these? Tom, can you confirm actually which modules are required or all are required?
Hi Ernia,
Can you please explain why the
cat: can't open '/home/slitaz/wok/linux64-wireless/taz/inux64-wireless-*/files.list': No such file or directory
type of errors are thrown?
And also in a previous post you mentioned we need to add package receipt and create entries for the orphan module error. Is there a guideline/doc somewhere which I can follow? I am confused about what should be the directory name, where I can add the orphan module name etc.
Offline
I have compiled with 3.2.40-new.txt config file (attached). Attached the logs as well.
There are two sets of errors:
[c]cat: can't open '/home/slitaz/wok/linux64-acpi/taz/linux64-acpi-*/files.list': No such file or directory
cat: can't open '/home/slitaz/wok/linux64-agp/taz/linux64-agp-*/files.list': No such file or directory
cat: can't open '/home/slitaz/wok/linux64-aoe/taz/linux64-aoe-*/files.list': No such file or directory
...[/c]
which I think can be ignored as I am trying to build a 32-bit kernel as of now.
For the other set:
[c]Orphan module: crc32c.ko.xz
Orphan module: ftdi-elan.ko.xz
Orphan module: virtio_console.ko.xz
Orphan module: i2c-designware-core.ko.xz[/c]
I need some guidelines on how to create a new package as I have posted above.
Question for Tom: Is 3.2.40-new.txt is the correct config file with the fix for the IDE issue? Because otherwise the linux.slitaz.config.txt config file you attached last builds fine.
Offline
[ Generated in 0.018 seconds, 9 queries executed - Memory usage: 1.63 MiB (Peak: 1.77 MiB) ]